background image

Warnings and Safety Information—Please read carefully! 

 

Risk of fire and/or electric shock.  This product is to be installed by a qualified electrician only.      Installation 
requires knowledge of LED lighting luminaire electrical systems.  Do not attempt if unqualified.

 

 

Do not expose wiring to sheet metal edges or other sharp objects to prevent damage.

 

 

Fixture is suitable for damp locations.  

 

 

Install in accordance with all national and local electrical codes. Manufacturer assumes no responsibility for the 
improper installation or application of this fixture.

 

 

Contact the manufacturer for any questions or concerns regarding installation of this fixture. 

 

 

Warning: This product is sensitive to Electrical Static Discharge (ESD).  Care should be taken to avoid 
direct contact with the LEDs.  Installers should be grounded using a wrist strap or other suitable method 
of grounding. Failure to ground the installer may cause pre-mature failures and void the fixture war-
ranty.  

 

Included Materials (Fig.1.1) 

A:  (1) Gas Canopy Lamp / Junction Box / 

Mounting Assembly 

B:  (1) Mounting frame with rivet nuts 
B:  (1) Cutting and drilling template 
C:  (2) Hex head 10-32 thread-forming 

screws 

D:  (4) Phillips head 10-32 machine screws 

with captive toothed lock washer 

 

 
 
 
 
 

 
 
 
 

 
 
 
 

 
 
 
 

Tools needed 

1.  Reciprocating saw, capable of sawing through the material of the gas canopy onto which this lumi-

naire is being installed. 

2.  Electric drill/driver, of sufficient power/speed to drill 5/16” holes through the material of the gas 

canopy. 

3.  5/16” twist drill, suitable for drilling through the material of the gas canopy 
4.  7/32” twist drill, suitable for drilling through the material of the gas canopy 
5.  #2 Phillips-drive bit for the electric drill/driver 
6.  5/16” nutdriver bit for the electric drill/driver 
7.  Wrenches suitable for the attachment of conduit / junction box components 
8.  Center punch 
9.  Phillips screwdriver 
10. Permanent marker 
11. Metal file 

FLED-R

 

Double-Deck Gas Canopy 

Installation  Instructions 

WHITEWAY LIGHTING, A Division of Hubbell Lighting Inc

1085 Johnson Drive, Buffalo Grove, IL 60089

800-544-4848  |  www.

hubbelllighting.com

Summary of Contents for FLED-R

Page 1: ...oid the fixture war ranty Included Materials Fig 1 1 A 1 Gas Canopy Lamp Junction Box Mounting Assembly B 1 Mounting frame with rivet nuts B 1 Cutting and drilling template C 2 Hex head 10 32 thread forming screws D 4 Phillips head 10 32 machine screws with captive toothed lock washer Tools needed 1 Reciprocating saw capable of sawing through the material of the gas canopy onto which this lumi nai...

Page 2: ...cating saw cut out the rectangular hole For safety file the cut edges to remove sharp burrs 3 Drill the 5 16 and 7 32 holes at the indicated locations 4 Insert the Mounting frame into the rectangular hole oriented with its long tabs facing upwards FLED R Double Deck Gas Canopy Installation Instructions WHITEWAY LIGHTING A Division of Hubbell Lighting Inc 1085 Johnson Drive Buffalo Grove IL 60089 8...

Page 3: ...6 As shown in the following sequence hang the Luminaire Assembly from the tabs on the Mounting Frame using the attached lanyard FLED R Double Deck Gas Canopy Installation Instructions WHITEWAY LIGHTING A Division of Hubbell Lighting Inc 1085 Johnson Drive Buffalo Grove IL 60089 800 544 4848 www hubbelllighting com ...

Page 4: ... box attach all conduit box fittings and connect the electric service line to the appropriate leads in the junction box 11 Lift the luminaire assembly up into the gas canopy tucking the lanyard into the gas canopy s interior space FLED R Double Deck Gas Canopy Installation Instructions WHITEWAY LIGHTING A Division of Hubbell Lighting Inc 1085 Johnson Drive Buffalo Grove IL 60089 800 544 4848 www h...

Reviews: