background image

Part Desc 

. . . . . . . . . . . . . . . . . . . . . . . . . Qty

4924B 

24" Jig Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965A 

32" Fence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965B 

Sled Base . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

4965C 

Fence Brackets, Pair . . . . . . . . . . . . . . . . . . . . . . . . 1

4965D 

Track Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

6305A 

Outboard Clamp Bracket . . . . . . . . . . . . . . . . . . . 2

6305IC 

Inboard Clamp.  . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

4519 

Straight Flip Stop . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Parts List

4965 Super Sled

Owners Manual

Please Read Carefully!

Part# Description Qty.

5760B Oval 

Nut 

5

Part# Description Qty.

HB030 1" 

Bolt 

3

Part# Description Qty.

BUSH004 5/8" Spacer 

1

Part# Description Qty.

WS002 Washer 

6

BEFORE BEGINNING

 

Identify and verify that you have all the parts listed in 

the parts list above, plus the parts shown on this page. Read 
through the instructions at least once before beginning. You'll 
need a #2 & #3 Phillips screwdriver for assembly.
 

The Super Sled is designed to be used on a table saw at 

least a 27" deep with a 3/8" x 3/4" miter slot that's between 
4-1/2" and 7-1/2" from the blade, measured from the blade 
side edge of the slot. It can be used in the left or right miter 
slot. Do not attempt to use on table saws with tables smaller 
than 27". If necessary, add additional supports to your saw to 
prevent the saw from tipping. 
 

For the Super Sled to work properly, the miter slot of 

your saw must be parallel to the saw blade. If this is not the 
case, make those adjustments to your saw before proceeding.

Part# Description Qty.

BUSH001 1/8” 

Spacer 

2

Part# Description Qty.

5590 Knob 

1

Part# Description Qty.

MF006 5/8" 

Screw  4

Part# Description Qty.

NUT025 Square 

Nut 

4

Part# Description 

Qty.

5864 Ratchet 

Handle 2

Part# Description Qty.

5540 T-Knob 

2

Part# Description Qty.

BUSH002 1/4" Spacer 

2

Part# Description Qty.

4965PA Index 

Pin 

2

Part# Description Qty.

5505 Thumb 

Screw 

1

Part# Description Qty.

MP150 1-1/2" 

Screw  2

Summary of Contents for 4965 Super Sled









Reviews: