background image

 

 

Instructions to the panel/ 

planer PH365 

IdNr 2014-365-000-1

 

 

We hope that you will get a lot of 
pleasure and use from your new 
woodworking machine. The following 
points should be observed to ensure 
trouble-free use. 
 
 

IMPORTANT! 

 
 

General 

Check the machine as soon as it 
delivered. 
Any damage caused during 
transportation 
should be reported immediately to the 
transport company. 
 
All guards and plates must be 
mounted before the machine is used. 
 

LIFTING MACHINE using forklift or 
pallet truck 
 
When replacing parts, use only 
genuine parts and note that all electric 
must be installed by a professional. 
 
 
 
 

Floor space 
The machine needs a space on 2 
m width 
The length depending on how 
long working pieces are. Min 
length is 5 m. 

 

 

 
 
 

 

Anchoring

 

For maximum safety the machine 
anchored to the floor with screws. Dia. 
8-10 mm. 
 

Application 

The machine can be used to mould 
and panel planing wood, particle 
board, board, etc.. 
Difficult materials such as chip board, 
teak wood, MDF, etc. requires carbide 
steel. 
The machine is made for indoor and 
temporary outdoor use.

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Summary of Contents for PH365



























Reviews: