background image

Manuel_X_232_EN 

1 / 13

 

27.01.2016 

 

X-Sensors AG 
Landenbergerstrasse 13 
CH-8253 Diessenhofen 
T: Intl. (0)52 657 38 77 
F: Intl. (0)52 741 47 66 
 

 

Configurable Load Measuring Interface CLMI X-232 

Operation Manual 

Rel.: Jan. 2016 

Table of content 

 

General technical informations ...................................................... 2 

 

Content of delivery ................................................................ 2 

 

Introduction & usage ............................................................. 2 

 

Mecanical dimensions........................................................... 3 

 

Configurations ....................................................................... 3 

 

Degree of protection, mounting ............................................ 3 

 

Installation ........................................................................................ 4 

 

Some reflections to the minimum load measurement .......... 4 

 

Background information about the floor detection ................ 4 

 

Truth table of the external sensor ......................................... 5 

 

Electrical installation ............................................................. 5 

 

Typical installation, minimum configuration .......................... 6 

 

Advances installation ............................................................ 6 

 

Commissioning ................................................................................ 7 

 

Commissioning, easy installation .......................................... 7 

 

Commissioning, advanced installation .................................. 7 

 

Description of in- and outputs ............................................... 8 

 

Position and orientation of the terminals............................... 8 

 

Programmable functions ....................................................... 9 

 

Setup menu ........................................................................... 9 

 

Menu-structure .................................................................... 10 

 

Technical data ..................................................................... 11 

 

Troubleshooting, diagnostic ........................................................ 11 

 

Frequently asked questions (FAQ) ..................................... 11 

 

Installation, general rules .................................................... 12 

 

Maintenane, repairing ......................................................... 12 

Summary of Contents for CLMI X-232














Reviews: