background image

1

For more cool and exciting XTM Racing products, visit our website at http://xtm.globalhobby.com

Thank you for purchasing the XTM Racing Baja Bullet RTR 2WD electric truck.  These Operating Instructions are provided
to help you enjoy your new Baja Bullet without any of the hassles you might expect.  Please read through all of the literature
that is provided with your truck.  Doing so will help you become familiar with how your truck and radio system operate.

IMPORTANT

Before running your new truck, please read and understand the warnings listed on the next page.  Failure to do so could lead to bodily
harm and/or injury.  The XTM Racing Baja Bullet RTR 2WD electric truck is not intended for those under 12 years of age, unless
closely supervised by an adult.

XTM Racing products are distributed exclusively by Global Hobby Distributors  18480 Bandilier Circle, Fountain Valley, CA  92728

All contents copyright © 2002, Global Hobby Distributors  Version V2.0 March 2002

Baja Bullet Truck Features:

Built and Ready-to-Run

Electronic Speed Control

Full Ball Bearing Set

Painted Body with Decals

Powerful 21 Turn Motor

2 Channel Radio System Preinstalled

OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Baja Bullet ESC Features:

Forward, Brake & Reverse

Micro Processor Control

Input Voltage: 6V - 12V

Frequency: 3Khz

Continuous Current: 20Amps

BEC Cutoff: 5V/2Amps

Temperature Cutoff: 80º Celsius

Weight: 2.4 Ounces

Summary of Contents for Baja Bullet

















Reviews: