background image

SPECIFICATIONS 

Model  .........................................6M5X 
Frequency ...................................50-50.5 + FM dims. 
Gain ............................................9.4 dBd 
Front to back ...............................21 dB typ. 
Beamwidth   ................................E=42

o

 / H=52

VSWR .........................................1.1 @ 50.175 MHz 
Power Handling ..........................1.5 kW 
Match Type .................................'T' Match 
Balun ...........................................4:1 Coaxial 
Turning radius .............................11 ft. 
Recommended Stacking ............15-21’.High 19-23’. Wide  
Feed Impedance / Conn. ............50 Ohms / “SO-239 
Lightning Protection ....................All Elements Grounded 
Boom length / Dia .......................18’ / 1-1/2" Dia 
Element Type .............................3/8" tube 
Mast Size ....................................1-1/2 to 2” nom. 
Wind area / Survival ...................2.2 sq. ft. / 100 MPH 
Weight / Ship wt. .........................9 lbs. / 11lbs. 

FEATURES 

The 6M5X is the latest computer optimized version of our 
popular 6M5. The 6M5X is two feet longer but front to back and 
gain are noticeably improved. We just made a good thing better 
maintaining low wind load and great performance for its size. It 
will compliment the rest of your antenna system and not 
overload your tower. Quick and easy to assemble, it is also 
great for mountain topping, grid expeditions and DXpeditions. 
The 6M5X features the same machined aluminum element 
mounting blocks, and sealed “T” match block,that all M

2

‘s use. 

The 6M5X is perfect for the Ham trying 6 meters for the first time 
or the seasoned vet who may stack them for lower angle of radiation or even some EME use. A tuning chart is included 
in the manual for the FM band. An upgrade kit is offered for older 6M5’s. 

5-4-99 
Rev  
7-24-03

 

Summary of Contents for 6M5X






Reviews: