Yale Real Living YRD220-ZW-619, Quick Start Manual

   Directions

   Components

Quick Start Instructions
Installation Instructions
Door Marker
Outside Escutcheon
Inside Escutcheon Assembly:
• Inside Mounting Plate
• Inside Escutcheon
• Battery Cover
4 AA Alkaline Batteries
Bolt
Strike Plate
Screw Pack (7 screws)
2 Keys 

For Technical Assistance call Yale: 

1-800-810-WIRE (9473).

1.  Install bolt in door.
     NOTE: The bolt must be in a retracted position    
     when installing the lockset.
     Attach with two (2) M4 x 25.4mm screws               
     supplied. 
2.  Install strike on the door frame.
3.  Route the cable through 2-1/8" diameter hole. 
     NOTE: Cable must go under bolt and through.
     See Detail A.
4.  Insert outside escutcheon while routing cable  
     through inside mounting plate’s 1/2" hole; insert  
     mounting plate “tongue” into bottom slot of            
     outside escutcheon and tailpiece through bolt.
5.  Secure inside mounting plate to outside  
     escutcheon using (2) M6 x 59.5mm pan head         
     machine screws. Do not over-tighten.
6.  Attach cable connector to inside escutcheon           
     circuit board (See Detail B above). Press firmly          
     with thumbs so that back edge (wires) of        

     connector lines up with arrows on PCB. 

CAUTION

: 

   Use care when assembling to ensure that cable     
   lies against the back recessed area of the inside           
   escutcheon. 
   Position and bend the cable, using the harness      
   clip as shown in Detail B to prevent binding   

   when installing the escutcheon over the mounting  
   plate.
7. Slide inside escutcheon over mounting plate. 

  8. Install and secure using (3) M4 x 8mm pan  

      head screws through the battery housing into       
      the mounting plate.
  9. Insert four (4) AA alkaline batteries. The lock      
      responds, “

Welcome to Yale Real Living

.”

       Note: Refer to programming instructions prior to  
       completion of step 10.

Touchscreen Deadbolt Quickstart Guide

Inside Mounting Plate

Inside Escutcheon

(3) M4 x 8mm
[8-32 x 5/16"] 

Pan Head Screws

(2) M6 x 59.5mm

[15/64 x 2-11/32"]

Pan Head Machine Screws

Outside Escutcheon

Battery Cover

5

7

8

10

Cable

4

6

See Detail B

9

3

Detail A

Inside Mounting Plate

(2) M4 x 25.4mm

[8-32 x 1"] 

Flat Head

Combination Screws

(2) M4 x 25.4mm

[8-32 x 1"] 

Flat Head

Combination Screws

1

2

   Tools Needed

ƒ

ƒ

Phillipsƒ#2ƒscrewdriverƒ

ƒ

ƒ

2-1/8"ƒ(54mm)ƒholeƒsaw

ƒ

ƒ

1"ƒ(26mm)ƒboringƒbit

ƒ

ƒ

7/64"ƒ(2.5mm)ƒdrillƒbitƒ

ƒ

ƒ

Chiselƒ&ƒhammer

Detail B

Forƒmoreƒinformationƒgoƒto:ƒwww.yalerealliving.com

Harness Clip

™

10. Install battery cover and tighten      
      screw with #2 Phillips screwdriver.

An ASSA ABLOY Group brand

P/N AYRD220-INST-QUK Rev B

Yale Real Living