background image

JOB DATA:

CHILLER MODEL NO. YT _______________

CHILLER MODEL NO. YT _____________________

NO. OF UNITS ________________________

NO. OF UNITS ______________________________

TYPE OF STARTING ___________________

TYPE OF STARTING _________________________

Included by YORK for Field Installation (by others) are:

YES

NO

PER UNIT

One – Two Unit Sequence Control Kit, Part No. 466-61597T

'

'

_____

Condenser Water Flow Switch

'

'

_____

________________________________________________________

'

'

_____

________________________________________________________

'

'

_____

PRODUCT DRAWING

YORK INTERNATIONAL CORPORATION

P.O. Box 1592, York, PA  17405

CONTRACTOR _______________________

PURCHASER ____________________________________________

ORDER NO. __________________________

JOB NAME _______________________________________________

YORK CONTRACT NO. _________________

LOCATION _______________________________________________

YORK ORDER NO. ____________________

ENGINEER ______________________________________________

REFERENCE

DATE ________

APPROVAL

DATE ________

CONSTRUCTION

DATE ________

Supersedes:  Nothing

Form 160.55-PW7 (899)

WIRING DIAGRAM

FIELD CONTROL MODIFICATIONS

MILLENNIUM™ MODEL YT CHILLERS (STYLE J)

Millennium chiller design allows for ease of interfac-
ing with Energy Management Systems (EMS). The
Graphic Control Center includes unit status contacts,
provisions for remote control inputs and provisions for
remote setpoint reset of leaving chilled liquid tempera-
ture and current limit for EMS interfacing. See Note 7.

Five sets of unit status contacts are factory furnished
through a field wiring terminal board in the Graphic Con-
trol Center. Each set of contacts are single pole, nor-
mally open, rated at 5 amperes resistive at 240VAC.
Chiller status contacts are provided for unit:

• Remote Mode Ready to Start – See Fig. 1.

• Cycling Shutdown – See Fig. 2.

• Safety Shutdown – See Fig. 3.

• Run (System Operating) – See Fig. 4.

• Anticipatory/Alarm – See Fig. 5.

Four sets of inputs are available to the EMS, allowing
for remote control of unit operation. Input device con-

tact rating shall be 5 milliamperes at 115VAC. Field wir-
ing terminal board (TB4) in the Graphic Control Center
permits connection for the following operation:

• Remote Stop Contacts – See Fig. 6.

• Remote Start Contacts – See Fig. 6.

• Remote/Local Cycling Devices – See Fig. 7.

• Multi-unit sequence – See Fig. 8.

The chiller should not be cycled by the Energy Manage-
ment System because the large motor used to drive the
centrifugal compressor is limited to one start per 30 min-
utes. Instead, it is possible to limit the compressor motor
amp draw indirectly or directly by the following meth-
ods:

1. Application of Sequence Control Kit, so only one

unit is running, when a single unit can carry the
cooling load – See Fig. 10.

2. When multiple unit installations are controlled by

an EMS, remote start and stop contacts are avail-
able to start and stop each chiller per Fig. 6. Con-
tact rating shall be 5 milliamperes at 115 volts A.C.

ENERGY MANAGEMENT SYSTEMS

Summary of Contents for MILLENNIUM YT J

















Reviews: