background image

               

FOR YOUR SAFETY

Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance

.

WARNING: Improper installation, adjustment, al-
teration, service or maintenance can cause injury
or property damage. Refer to this manual. For as-
sistance or additional information, consult a quali-
fied installer, service agency or the gas supplier.

         

FOR YOUR SAFETY

    WHAT TO DO IF YOU SMELL GAS

Do not try to light any appliance.

Open windows.

Do not touch any electrical switch;
do not use any phone in your building.

Extinguish any open flame.

Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.

If you cannot reach your gas supplier, call the
fire department.

IAMON

80

D

D

UPFLOW

® 

MULTI-POSITION GAS-FIRED FURNACES

INDUCED-DRAFT STYLE G

INSTALLATION INSTRUCTION

Supersedes:  650.69-N3Y (1294)

650.69-N3Y (1095)

035-13581

CAUTION

THIS PRODUCT MUST BE INSTALLED IN STRICT COM-
PLIANCE WITH THE ENCLOSED INSTALLATION IN-
STRUCTIONS AND ANY APPLICABLE LOCAL, STATE, AND
NATIONAL CODES INCLUDING BUT NOT LIMITED TO,
B U I L D I N G ,   E L E C T R I C A L   A N D   M E C H A N I C A L
CODES.

WARNING

IMPROPER INSTALLATION MAY CREATE A CONDITION
WHERE THE OPERATION OF THE PRODUCT COULD
CAUSE PERSONAL INJURY OR PROPERTY DAMAGE.

IA

MON

80

D

D

HORIZONTAL (LEFT)

IAMON

80

D

D

HORIZONTAL (RIGHT)

MODELS: P2MP (U.S.) - STYLE G
     P9MP 

(Canada) 

STYLE 

E

(Upflow/Horizontal)
32-112 MBH OUTPUT

IAMON

80

D

D

DOWNFLOW

MODELS P2DP - 
STYLES C, D
(Downflow)
48-104 MBH OUTPUT

DIAMOND SERIES FURNACES

Summary of Contents for P2DP Series

























Reviews: