background image

RESEARCH&DEVELOPMENT OF AMERICA, INC.

www.yoshimura-rd.com

5420 DANIELS STREET STE A, CHINO CA., 91710 

·

 (800) 634-9166 

·

 (909) 628-4722 

·

 FAX (909) 591-2198

NOTE:  IN THE STATE OF CALIFORNIA, IT IS ILLEGAL TO MODIFY THE EMISSION CONTROL SYSTEM,  WHICH INCLUDES THE CARBURETORS OF ANY VEHICLE.

You must know how to remove and replace your stock exhaust in order to install this product 
otherwise have it installed by a professional mechanic. Keep all stock parts from your existing 
system as some components may be necessary to install your new Yoshimura exhaust depending 
on the application. Read through all instructions before beginning installation. Exhaust system can 
be extremely hot. Let motorcycle cool down before beginning installation. Always wear hand and 
eye protection and take precautionary measures to avoid injury. 

Race Series systems are:
• NOT CARB/EPA tail-pipe emissions compliant.
• NOT street legal. 
• For “Closed Course Competition” use only. 

RACE SERIES

Qualified Manufacturer Declared “Modified Part ”

13100CP520   (SS/CF)

13100NP720   (TI/CF)

Alpha Taper 3/4 System

Yamaha FZ-10 / MT-10

FOR CLOSED COURSE COMPETITION ONLY; NOT INTENDED FOR STREET USE

2017 ~ 2021

Summary of Contents for RACE 13100CP520








Reviews: