background image

SURE SHOT

®

SPRAYERS

INSTRUCTIONS

Refillable, reusable.  Extra versatile.

Pressurized by free air

DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS

1) ALWAYS DEPRESSURIZE SPRAYER BEFORE

REMOVING ANY PARTS.

The pressure may be let

out of the sprayer one of the two following ways:

a) Tip  the  sprayer  upside  down  and  depress  the

trigger  until  no  pressure  is  left.  If  some  liquid
is  left  in  the  sprayer  when  you  attempt  this
procedure  make  sure  you  aim  the  nozzle  at  a
place where a little bit of liquid can be expelled.

b) Remove  #122  black  cap  from  air  filler  and  use

small  probe  to  depress  #121  valve  core  until 
all  the  pressure  escapes. 

NOTE: 

Make  sure 

the  sprayer  is  upright  and  the  air  filler  stem  is
pointing  away  from  you  when  depressing  the
valve core. 

c) Remove  the  complete  top  assembly  from  the

canister  once  all  the  air  has  been  let  out.    Do 
this  by  grasping  the  body  in  one  hand  and  the
canister  in  the  other  while  unscrewing 
counterclockwise completely.

2)

Fill  sprayer  2/3  full  (24  ounce  maximum  liquid 
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.

NOTE:  ALWAYS  CHECK  WITH YOUR  CHEMICAL

SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.

READ CAUTION LABEL ON SPRAYER BEFORE FILLING.

NEVER USE ACIDS IN ANY

SURE SHOT SPRAYER.

3)

Take  the  complete  top  assembly  and  screw  it 
clockwise  into  top  of  the  canister.    Firmly  hand 
tighten only.

4)

Charge  sprayer  with  compressed  air  by  holding
standard  air  chuck  on  valve  stem  of  the  air  filler.
Hold the air chuck on the air filler until you hear the
line  pressure  equalize  with  the  sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray  the  full  24  oz.  without  a  recharge  of  air.

THE  MAXIMUM  PRESSURE  SHOULD  NOT

EXCEED 200 PSI.

5)

The Model “M” sprayer is now ready to use.

6)

For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.

CAUTION:

Never  point  the  nozzle  of  sprayer  toward

yourself  or  another  person.  Always  point  the  nozzle
of  the  sprayer  away  from  yourself  and  toward  your
intended target before depressing the trigger.

MODEL M

24 OZ.

ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS

SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS

MAXIMUM PRESSURE 200 PSI

SURE SHOT

®

SPRAYERS

INSTRUCTIONS

Refillable, reusable.  Extra versatile.

Pressurized by free air

DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS

1) ALWAYS DEPRESSURIZE SPRAYER BEFORE

REMOVING ANY PARTS.

The pressure may be let

out of the sprayer one of the two following ways:

a) Tip  the  sprayer  upside  down  and  depress  the

trigger  until  no  pressure  is  left.  If  some  liquid
is  left  in  the  sprayer  when  you  attempt  this
procedure  make  sure  you  aim  the  nozzle  at  a
place where a little bit of liquid can be expelled.

b) Remove  #122  black  cap  from  air  filler  and  use

small  probe  to  depress  #121  valve  core  until 
all  the  pressure  escapes. 

NOTE: 

Make  sure 

the  sprayer  is  upright  and  the  air  filler  stem  is
pointing  away  from  you  when  depressing  the
valve core. 

c) Remove  the  complete  top  assembly  from  the

canister  once  all  the  air  has  been  let  out.    Do 
this  by  grasping  the  body  in  one  hand  and  the
canister  in  the  other  while  unscrewing 
counterclockwise completely.

2)

Fill  sprayer  2/3  full  (24  ounce  maximum  liquid 
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.

NOTE:  ALWAYS  CHECK  WITH YOUR  CHEMICAL

SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.

READ CAUTION LABEL ON SPRAYER BEFORE FILLING.

NEVER USE ACIDS IN ANY

SURE SHOT SPRAYER.

3)

Take  the  complete  top  assembly  and  screw  it 
clockwise  into  top  of  the  canister.    Firmly  hand 
tighten only.

4)

Charge  sprayer  with  compressed  air  by  holding
standard  air  chuck  on  valve  stem  of  the  air  filler.
Hold the air chuck on the air filler until you hear the
line  pressure  equalize  with  the  sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray  the  full  24  oz.  without  a  recharge  of  air.

THE  MAXIMUM  PRESSURE  SHOULD  NOT

EXCEED 200 PSI.

5)

The Model “M” sprayer is now ready to use.

6)

For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.

CAUTION:

Never  point  the  nozzle  of  sprayer  toward

yourself  or  another  person.  Always  point  the  nozzle
of  the  sprayer  away  from  yourself  and  toward  your
intended target before depressing the trigger.

MODEL M

24 OZ.

ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS

SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS

MAXIMUM PRESSURE 200 PSI

SURE SHOT

®

SPRAYERS

INSTRUCTIONS

Refillable, reusable.  Extra versatile.

Pressurized by free air

DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS

1) ALWAYS DEPRESSURIZE SPRAYER BEFORE

REMOVING ANY PARTS.

The pressure may be let

out of the sprayer one of the two following ways:

a) Tip  the  sprayer  upside  down  and  depress  the

trigger  until  no  pressure  is  left.  If  some  liquid
is  left  in  the  sprayer  when  you  attempt  this
procedure  make  sure  you  aim  the  nozzle  at  a
place where a little bit of liquid can be expelled.

b) Remove  #122  black  cap  from  air  filler  and  use

small  probe  to  depress  #121  valve  core  until 
all  the  pressure  escapes. 

NOTE: 

Make  sure 

the  sprayer  is  upright  and  the  air  filler  stem  is
pointing  away  from  you  when  depressing  the
valve core. 

c) Remove  the  complete  top  assembly  from  the

canister  once  all  the  air  has  been  let  out.    Do 
this  by  grasping  the  body  in  one  hand  and  the
canister  in  the  other  while  unscrewing 
counterclockwise completely.

2)

Fill  sprayer  2/3  full  (24  ounce  maximum  liquid 
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.

NOTE:  ALWAYS  CHECK  WITH YOUR  CHEMICAL

SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.

READ CAUTION LABEL ON SPRAYER BEFORE FILLING.

NEVER USE ACIDS IN ANY

SURE SHOT SPRAYER.

3)

Take  the  complete  top  assembly  and  screw  it 
clockwise  into  top  of  the  canister.    Firmly  hand 
tighten only.

4)

Charge  sprayer  with  compressed  air  by  holding
standard  air  chuck  on  valve  stem  of  the  air  filler.
Hold the air chuck on the air filler until you hear the
line  pressure  equalize  with  the  sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray  the  full  24  oz.  without  a  recharge  of  air.

THE  MAXIMUM  PRESSURE  SHOULD  NOT

EXCEED 200 PSI.

5)

The Model “M” sprayer is now ready to use.

6)

For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.

CAUTION:

Never  point  the  nozzle  of  sprayer  toward

yourself  or  another  person.  Always  point  the  nozzle
of  the  sprayer  away  from  yourself  and  toward  your
intended target before depressing the trigger.

MODEL M

24 OZ.

ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS

SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS

MAXIMUM PRESSURE 200 PSI

SURE SHOT

®

SPRAYERS

INSTRUCTIONS

Refillable, reusable.  Extra versatile.

Pressurized by free air

DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS

1) ALWAYS DEPRESSURIZE SPRAYER BEFORE

REMOVING ANY PARTS.

The pressure may be let

out of the sprayer one of the two following ways:

a) Tip  the  sprayer  upside  down  and  depress  the

trigger  until  no  pressure  is  left.  If  some  liquid
is  left  in  the  sprayer  when  you  attempt  this
procedure  make  sure  you  aim  the  nozzle  at  a
place where a little bit of liquid can be expelled.

b) Remove  #122  black  cap  from  air  filler  and  use

small  probe  to  depress  #121  valve  core  until 
all  the  pressure  escapes. 

NOTE: 

Make  sure 

the  sprayer  is  upright  and  the  air  filler  stem  is
pointing  away  from  you  when  depressing  the
valve core. 

c) Remove  the  complete  top  assembly  from  the

canister  once  all  the  air  has  been  let  out.    Do 
this  by  grasping  the  body  in  one  hand  and  the
canister  in  the  other  while  unscrewing 
counterclockwise completely.

2)

Fill  sprayer  2/3  full  (24  ounce  maximum  liquid 
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.

NOTE:  ALWAYS  CHECK  WITH YOUR  CHEMICAL

SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.

READ CAUTION LABEL ON SPRAYER BEFORE FILLING.

NEVER USE ACIDS IN ANY

SURE SHOT SPRAYER.

3)

Take  the  complete  top  assembly  and  screw  it 
clockwise  into  top  of  the  canister.    Firmly  hand 
tighten only.

4)

Charge  sprayer  with  compressed  air  by  holding
standard  air  chuck  on  valve  stem  of  the  air  filler.
Hold the air chuck on the air filler until you hear the
line  pressure  equalize  with  the  sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray  the  full  24  oz.  without  a  recharge  of  air.

THE  MAXIMUM  PRESSURE  SHOULD  NOT

EXCEED 200 PSI.

5)

The Model “M” sprayer is now ready to use.

6)

For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.

CAUTION:

Never  point  the  nozzle  of  sprayer  toward

yourself  or  another  person.  Always  point  the  nozzle
of  the  sprayer  away  from  yourself  and  toward  your
intended target before depressing the trigger.

MODEL M

24 OZ.

ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS

SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS

MAXIMUM PRESSURE 200 PSI

DURA SHOT

 S SPRAYERS

DIRECTIONS FOR OPERATING 

DURA SHOT

™ 

S

 

SPRAYERS

DURA SHOT

 S

 

SPRAYER.

DURA SHOT S

24 oz.

The 

DURA SHOT

 sprayer is now ready to use.

2)  Connect the sprayer to the quick connect on the 

machine (Pictured below). Push the joystick to the 

RIGHT (liquid side) of the machine until the yellow 

cap on the rod moves all the way to the right 

(approx. 15 seconds) and stops.

a)  Always use the entire product in sprayer before 

you refill as this will make sure you will have 24 

oz. on your next fill.

b)

c)

3)  Release the control lever; make sure it returns to 

center for several seconds, then push lever to the 

LEFT for air, and hold for approx. 15 seconds. This 

will fill the sprayer with up to 125 P.S.I. of air and 

siphon the chemical back into the pump so you are 

ready for the next fill. (If you do not hold the lever to 

the left long enough the rod will retract slightly 

indicating a short fill. Push the lever back to the left 

for an additional 5 seconds and release.)

4)   Disconnect the quick connect from top of sprayer by 

pulling the outside collar of the quick connect until it 

releases. You are ready to spray.

CAUTION:

  Never point the nozzle of sprayer toward yourself 

or another person. Always point the nozzle of 

the sprayer away from yourself and toward your 

intended target before depressing the trigger.

ALWAYS DEPRESSURIZE THE SPRAYER BEFORE 

REMOVING ANY PARTS.
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS.
MAXIMUM PRESSURE 200 PSI.

Reviews: