Remote Control instruction
/ /
.
Read the safety instructions on the enclosed sheet carefully before you start installation.If these instructions are not followed,LIANDA
industry’s liability and warranty are forfeited.
LIANDA is not liable for any change in the regulations and standards introduced following the publication of this manual.
LIANDA hereby declares that the short range product complies with directive 1999 5 CE
This product must be installed and programmed by qualified personnel.Read these instructions carefully before making the connections.
Warning
,
,
,
to
,
.)
The Remote Control is a short range emitter radio control
device for various applications such as blinds shutters
projection screens awnings and more.It can be used
all
the Lianda RTL receivers(Some Receivers have limited
functions with the RTL please read the complete instruction
for more information
1.Product Description
2.Technical Information
.Frequency:433.92 MHz
.Temperature:-10
to +50
. attery Type:CR2032 Lithium 3V DC 1 5
channels / 27A 12V DC 15 channels
.Product Class:II with installation completed
℃
℃
B
( &
)
(
)
(
)
Rev :X01
.
Zhejiang Lianda Science Technology Co
Ltd
&
.,
The Remote Controls are able to control 15 groups of motors at most
RTL motors or motors equipped with RTL receives
(
) .
The Remote Controls can be used to setup the limit of the RTL Radio
motor with radio limit setting
.
3.Functions
SCE-R5
SCE-R1
[ ] :
(
)
(
)
(
)
( &
)
a
UP control key
b
STOP control key
c
DOWN control key
d
LED 1 5channels
LCD(15channes)
e
f
[ ] :
[ ] :
[ ] :
[ ] :
[ ] :
(
)
[ ]
PROG
Selection key 5channels
g :DEC(decrease channel)
[h] :INC (increase channel )
4.Open the emitter Replace the battery
/
.
.
.
.
( -
)
.
.
1) Open the back cover
2) Remove the old battery and place the new battery
1 5channels:CR2032 Lithium 3V,15 channels: 27A 12V
3) Close the back cover
Add Economic Development Zone2 Nanxun HuZhou Zhejiang Province China
:
,
,
,
,
Customer service number: 86 572 3787117
+
-
-
P C 313009 Fax 86 572 3911465
E MAIL info lianda lianda com
Website http
www lianda com
. :
:
-
-
-
:
-
@
.
:
: / /
.
.
5.Programming
Important remark The programming and direction checking
should be done after the motor is
installed
:
.
completly
1 .Record a Remote Control in a tubular motor
)
-
.
-
+
.
-
.
Switch the power on
Press UP DOWN buttons of the remote control together
A Feedback will confirm that remote control has been memorized
inside the memory of the tubular motor
ON
0 5 sec
.
.
Feedback
Feedback jog is a short up and down movement of the motor
=
:
.
SCE-R15
1). LCD instruction(15 channels):
.Channel number displays the number of current channel.
.Command icon displays that the control is sending command.
The UP icon flashes when UP button is pressed
The STOP icon flashes when STOP button is pressed
The DOWN icon flashes when DOWN button is pressed
When PROG button is pressed, three icons would flash together.
.Low battery icon will display when the power of battery is low.
;
;
;
2). “Sleep” and “Wake up”(15 channels):
The LD-15C RTL remote control has the function of “
”
and “
” .
.
: If there is no button action in 5 seconds, the Remote
Control will fall into
mode,the power will be shut down
and LCD will be turned off.
.
: During the
mode, pressing any button, the
Remote Control will be woke up, LCD will display the channel
number which is displayed before it is turned off.
Sleep
Wake up
Sleep
Sleep
Wake up
Sleep
Channel number
Low battery icon
Command
Up
Stop & Down
(
,
)
SCE-R1,R5
SCE-R15
[ ]
a
[ ]
b
[ ]
c
[ ]
d
[ ]
e
[ ]
a
[ ]
b
[ ]
c
[ ]
d
[ ]
e
[ ]
f
[ ]
a
[ ]
b
[ ]
c
[ ]
e
[ ]
h
[ ]
g
1
2
4
m
m
24mm
48mm
-
+
=
.
433 92MHz
50m
=
.
433 92MHz
5m
2.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
（
(1) This device may not cause harmful interference, and
（
(2) This device must accept any interference received, including interference that may cause undesired operation.
（
Attention that changes or modification not expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This product
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this product does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
RTA
RTA
RTA
RTA
RTA
