804053UK CS Res Quick Start Guide June 2016 - V3.01
Quick Start Guide
•
Before proceeding, read the Installation instructions and User manual.
•
Check all the components are present and correct.
•
Check that you have all the necessary tools.
•
Ensure the under-counter cupboard floor can support the product weight when full
of water,(check the specifications in the Installation instructions and allow an extra
5-8kg when full of water).
Note
This quick start guide must be read in conjunction with the Installation instructions
and User manual.
Step 2-
Cut cupboard holes and fit the air vent ducts.
Ventilation
Parts supplied
Description
Parts supplied
Description
1 x HydroTap
®
G4*
Classic, Elite
or
#
Arc / Cube
#
(inc. Tube kit)
1 x User manual and
1 x Quick start guide
1 x Installation
instruction
1 x
Command-
Centre
TM
with air
and water filters
1 x
CO
2
gas cylinder
assembly
2 x Outlet vent
1 x Inlet vent
1 x
Mains water
connection hose
801599 - HydroTap User Guide - Nov 2013 UK - V1.05
Page 1 of 20
ZIP HydroTap
User Guide
®
•
Tap Operation...................(Pages 2-5)
•
LCD Screen & Menu .......(Pages 6-18)
•
Maintenance.................... (Pages 18-20)
•
Date of Installation.........
Affix Model Number Label
Here
801599
BC160/125G4
BC240/175G4
BCH160/125G4
BCH240/175G4
AV160/125G4
AN160/125G4
AV240/175G4
AN240/175G4
801600 - Zip Quick Start Guide - October 2013 - V1.06
Parts Supplied
Description
Parts Supplied
Description
1 off
Hydrotap Tap
and hoses
Duct kit
1x Air Duct
1 x Mounting
plate
1 off
Undersink Unit
with air and water-
filter
Vent kit
1 x Kickboard
louvre
1 x Door vent
louvre
1 x front vent grill
1 x Restrictaflow
valve and Tee
piece for Mixer
Taps
1 off
HydroTap
Booster heater
and hoses
(Supplied with
240/175 models)
1 off Mains water
connection hose
QUICK START GUIDE
Note: This quick start guide must be read in conjunction with
the main installation and user instructions
•
Before proceeding, read the installation and user instructions
•
Check all the components are present and correct.
•
Check that you have all the necessary tools
•
Ensure the underbench can support the product weight when full of water,
(Check the specifications in the main book and allow an extra 5-8kg when full. )
Before installing ensure the following have been provided at
the installation site:
•
Sufficient space in the cupboard to install all of the undersink units in accordance
with these Installation Instructions. Refer to technical specification for dimensions. If
required, make allowance for a booster heater. (Refer to the main book, for detailed
installation instructions).
•
A potable water supply connection with isolating valve inside the cupboard within
reach of the flexible braided hose and positioned so that the connection point and the
stop cock will not be obstructed when all the undersink units are installed.
•
For Zip HydroTap 160/125 &160/175 models, a 220-240Vac, 10A GPO will be
required. For Zip HydroTap 240/175 models, two 220-240Vac, 10A GPOs will be
required. (One GPO is for the Zip HydroTap and the other for the Booster heater).
NOTE: Check the cable lengths and outlet positions before proceeding.
•
A potable cold water supply with a minimum working pressure of 172kPa and a
maximum working pressure of 700kPa connected via an isolation valve.
•
For the mains pressure All-IN-ONE, both a hot and cold water supply will be required.
•
The undersink appliances must be mounted in upright positions as shown in the
diagrams.
IMPORTANT!
Do not proceed with the installation if these
requirements are not met.
STEP 1-
Prepare and fit the Taps
Hole positioning:
Position the tap such that it dispenses into
the sink bowl with ample clearance for a cup or tea pot. Alternatively,
the tap could be mounted away from the sink using a Zip Font, avail-
able as an accessory.
Apply a light smearing of silicon sealant
on the underside of the upper spacer to
ensure a watertight fi t.
For HydroTap and Mixer taps
cut a 35mm hole in the bench / sink top.
BENCH TOP
Ø35mm
HydroTap Tap
Mixer Tap
4-in-1
(If required)
NUT
LOWER RUBBER
WASHER
UPPER
RUBBER
WASHER
WASHER
BRAIDED
HOSE x 3
UPPER RUB-
BER WASHER
LOWER RUB-
BER WASHER
WASHER
NUT
White Hose
Ext. Mains
Blue band
Mixer IN
Red band
Mixer Out
O-RING
BASE
BLOCK
SPIDER
BASE
BLOCK
NUT
USB
CABLE
ALL
THREAD
ROD
NOTE: feed each of
the tubes and elec-
trical cable evenly in
between the legs of
the BASE BLOCK
SPIDER.
All-In-One Tap
(If required)
For AIO mains and vented Taps
Cut a 50mm hole in the bench / sink top.
NOTE: make sure the tap location will allow the nozzle to drain into the sink.
SINK TOP
50mm
ALL THREAD
ROD
STAINLESS
STEEL
WASHER
SPIDER
CLAMP
NUT
BLACK
PLASTIC
SPACER
NOTE: feed each of the three tubes and
electrical cable evenly in between the legs of
the SPIDER CLAMP when installing.
Fit the
STAINLESS STEEL
WASHER,
SPIDER CLAMP,
AND 6mm NUT.
6mm
NUT
SPIDER
CLAMP
Stainless
washer
Black plastic
spacer
35mm dia hole
Sink
O-RING
SINK TOP
Fit the O-ring to the underside of the AIO tap
then pass all hoses through the 50mm hole.
Chiller
connection
BLUE
From
Mixer OUT
to Tap - Vented version only
Boiler
connection
RED
Blue ring on
RHS mains IN to
Mixer IN
White ring
on LHS to
Mains in
Tap
O ring Base
Clear tube to Vent
* Tap options supplied are dependant
upon configuration purchased.
•
The Command-Centre
TM
must be mounted in upright positions, with base mounted
horizontally, as shown overleaf.
IMPORTANT!
Do not proceed with the installation if these requirements are not met.
Prior to installation, ensure that the following have been
provided at the installation site.
•
Sufficient space in the cupboard to install the Command-Centre
TM
and it’s ancillary
components. Refer to the Technical specification of the Installation instructions for
dimensions.
•
A potable water supply connection with min. / max. working pressures of: (refer
to the Technical specification of the Installation instructions for specific model
information).
•
An isolating valve inside the cupboard within reach of the flexible braided hose and
positioned so that the connection point and the stop cock will not be obstructed
when the Command-Centre
TM
and it’s ancillary components are installed.
•
For Zip HydroTap
®
G4, a single 220-240V AC, 13A socket is required.
•
The Command-Centre
TM
must be installed in accordance with IEE regulations, see
Technical specifications in the Installation instructions, for power ratings.
Note
Check the cable lengths and outlet positions before proceeding and ensure that the
tap location will allow the tap spout to drain into the sink.
Step 1-
Prepare and install the taps. Refer to 803341UK Tap installation instructions
(for Arc / Cube also refer to the tube kit assembly instructions) supplied with the tap.
.
Hole positioning
Position the tap such that it dispenses
into the sink bowl with ample clearance for a cup or tea pot.
Alternatively, the tap could be mounted away from the sink using
a Zip Font, available as an accessory. See Major components
and accessories, in the Installation instructions.
Apply a light smearing of silicon sealant on the
underside of the spacer to ensure a watertight fit.
HydroTap
®
G4 Classic & Elite tap installation
All thread
rod
Stainless
steel
washer
Spider
clamp
6mm nut
Black
plastic
spacer
Note
Feed each of the three tubes and USB cable evenly in
between the legs of the spider clamp during installation.
Fit the
stainless steel
washer, spider
clamp, and
6mm nut.
6mm
nut
Spider
clamp
Stainless steel
washer
Black plastic
spacer
Ø
35mm hole
HydroTap
®
G4 Classic & Elite taps
Cut a
Ø35mm hole in the worktop / sink.
Note
VENTILATION IS ESSENTIAL
Read ‘Step 2’ ‘Ventilation’ before you start.
HydroTap
®
G4 Classic
116
Tap
Recommended dispensing
distance (mm)
Elite
116
HydroTap
®
Classic
116
HydroTap
®
Arc/Cube
171 (-174 extended)
Tap installation special tool requirements
For the HydroTap
®
G4
•
35mm diameter sheet metal hole punch for sinks (not supplied).
•
35mm diameter hole saw for worktops (not supplied).
•
Nut runner tube spanner for fixing the tap assembly.
Hole positioning
Position the tap such that it dispenses into the
sink bowl with ample clearance for a cup or
tea pot. Alternatively, the tap could be mounted
away from the sink using a Zip Font, available
as an accessory. (See Major components and
accessories, Command-Centre
TM
Installation
instructions).
Tap positioning
Alternative arrangement
For high use applications where the
cupboard space temperature is near
35
0
C or higher, the vent kit supplied
can be used to provide further
ventilation by convection.
Note
The vent kit has to be
installed in a way that allows air
to be drawn in from the bottom of
the cupboard and expelled through
the top of the cupboard. The outlet
vent should be towards the top of
the door (position
A1
) or side of the
cupboard (position
A2
).
(Where possible air inlet vent
and the air outlet vent should be
positioned at opposite ends of the
same cupboard space).
Ventilation for all models
•
The clearance envelope dimensions stated in the specification sheets and installation
instructions must be observed.
•
Adequate ventilation must be provided to ensure that the cupboard space
temperature does not exceed 35
0
C.
Preferred arrangements
4mm door buffers (at the four corners of each door) supplied with the Command-Centre
TM
should be used to provide adequate ventilation in normal usage, see illustration below.
Door buffer
A1
A2
B
Vent cut-out details
A1 or A2 Air outlet vent
B Air inlet vent
Note
Flat outlet vent detail
shown, louvred
outlet vent also
supplied.
