Zummo Z22 Technical Instructions Download | Manualshive

Page: 1 / 13

background image

011319-03

1

Technical instructions

Z22

TECHNICAL INSTRUCTIONS FOR JUICE EXTRACTOR Z22

INDEX:

1.-

Disassemble machine

2.- Dismantling and change motor
3.-

Closing machine

4.-

Grating disc change

5.-

Electric diagram

6.-

Troubleshooting

1.- Disassemble machine

1.1.

This juicer machine has a metallic locking arm, that allows locking the machine up while

working. When the locking arm is unlocked, turns a micro-switch off and it makes that the
juicer doe

sn’t works and we can work safety. (Otherwise we should disconnect the mains

before doing anything with the machine)

1
2
3
...
»

Summary of Contents for Z22














Reviews:

No comments

Related manuals for Z22

BREKKY AND BANQUET

Brand: Sunbeam Pages: 28

Brand: Summit Pages: 8

Brand: Magic mill Pages: 20

Brand: JAC Pages: 106

Brand: Back to Basics Pages: 4

Brand: Saturn Pages: 11

Brand: Grizzly Pages: 4

Brand: La Sommeliere Pages: 124

Brand: Landmark Pages: 16

Brand: Metcalfe Pages: 16

Brand: salling Pages: 23

Brand: Eldom Pages: 36

Brand: K+G Wetter Pages: 24

Brand: Profi Cook Pages: 96

Brand: Bio Chef Pages: 16

CHATSWORTH 41301

Brand: Creda Pages: 12

Sonifer SW 4300

Brand: Orbegozo Pages: 30

Kenmore 27" Wide LAUNDRY CENTER Washer - Dryer

Brand: Kenmore Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands