Broadway Limited Paragon 2 Series Operator'S Manual Download

Page: 23 / 28

Paragon 2

CV188

Pitch Shift

Change to alter pitch
of all sounds. Makes 2
locomotives sound different

0-255

128

CV194

Articulated Chuff
Offset

Initial angular offset
between front and rear
drivers set in articulated
engine.

0-25

CV195

Slip Timer

Time in seconds for
articulated drivers to slip
one increment.

0-255

CV196

Steam Cocks

Number of wheel rotations
for which open steam cocks
are heard.

0-255

CV197

Rod Knock

Number of wheel rotations
for which open steam cocks
are heard.

0-255

CV208

DCC Cab Light
Throttle Stop (if equ
ipped)

If equipped, cab light is
turned on below this speed
step. 0 is always on. 255
is always off.

0-255

CV209

DCC Brake Set
Throttle Stop

Brake is set below this
throttle level.

0-128

CV210

DCC Brake Release
Throttle Stop

Brake is released when
speed exceeds this throttle
level.

0-128

CV 224

Horn Select

Selects one of 3 main
horns.

0,1,2

CV225

DCC Control One

see tech manual

CV226

DCC Control Two

see tech manual

CV227

FWD/Reverse
Warning

2 turns off horn toots to
ward when starting. 6
turns on.

2 or 6

CV229

DCC Extended Consist
Lighting

see tech manual

CV230

DCC Easy Consist

0=single locomotive,
1=front, 2=middle, 3-rear
locomotive in consist.

0,1,2,3

CV 231

Headlight brightness

Decrease to dim headlight
and rear light.

4-100

100

CV236

Smoke unit heat level

when moving

Set to higher level to

increase smoke while

moving.

0-90

Cv237

Smoke unit heat level

when stopped

Set to higher level to

increase smoke while

stopped.

0-50

CV238

Loop Repeat

Set to 64 plus the number
of repeats, up to 14. 65=
1 repeat, 66=2 repeat,
etc. Set to 79 to repeat

indefinitely.

65-79

CV239

Macro Loop Adjust

Increasing by 1 shortens
the playback loop by 0.1
second.

0-255

CV240

Random Sound
Generator Occurrence

Increasing decreases how
often random sounds
occur.

1-20

CV245

Enable Alternate Horn
Ending and start
delay

16=both disabled
17= horn ending enabled
18=Start Delay enabled.
19=Both enabled.

16,17,18,19

CV248

Motor Start Delay

sets start delay in 0.1
second increments.

0-255

Summary of Contents for Paragon 2 Series





























Search results

Summary of Contents for Paragon 2 Series

Reviews:

Related manuals for Paragon 2 Series

Brands by name

Popular brands

Broadway Limited Paragon 2 Series, Operator'S Manual

Search results

Summary of Contents for Paragon 2 Series

Reviews:

Related manuals for Paragon 2 Series

Brands by name

Popular brands