1-33
Cisco ASA Series CLI Configuration Guide
Chapter 1 Configuring a Cluster of ASAs
Configuring ASA Clustering
Examples
The following example configures the Management 0/0 and Management 0/1 interfaces as a device-local
EtherChannel, and then configures the EtherChannel as an Individual interface:
ip local pool mgmt 10.1.1.2-10.1.1.9
ipv6 local pool mgmtipv6 2001:DB8:45:1002/64 8
interface management 0/0
channel-group 1 mode active
no shutdown
interface management 0/1
channel-group 1 mode active
no shutdown
interface port-channel 1
nameif management
ip address 10.1.1.1 255.255.255.0 cluster-pool mgmt
ipv6 address 2001:DB8:45:1001/64 cluster-pool mgmtipv6
security-level 100
management-only
What to Do Next
•
For spanned interface mode, configure your data interfaces. See the
EtherChannels” section on page 1-33
•
For Individual interface mode, join the cluster. See the
“Configuring the Cluster Interface Mode on
Each Unit” section on page 1-30
Configuring Spanned EtherChannels
A Spanned EtherChannel spans all ASAs in the cluster, and provides load balancing as part of the
EtherChannel operation.
Prerequisites
•
You must be in Spanned EtherChannel interface mode; see the
“Configuring the Cluster Interface
Mode on Each Unit” section on page 1-30
.
•
For multiple context mode, start this procedure in the system execution space. If you are not already
in the System configuration mode, enter the
changeto system
command.
Step 6
security-level
number
Example:
hostname(config-if)# security-level 100
Sets the security level, where
number
is an integer between 0
(lowest) and 100 (highest). See the
Step 7
no shutdown
Example:
hostname(config-if)# no shutdown
Enables the interface.
Command
Purpose
Summary of Contents for 5505 - ASA Firewall Edition Bundle
