Cisco NM-1A-E3 User Manual Download

Page: 24 / 26

Configuring the Cisco NM-1A-T3/E3 Network Module

debug atm t3e3

Cisco IOS Release 12.4(15)T

Router(config-if)#

*Jun 27 22:12:28.816: ATM2/0: Setup_VC: vc:3 vpi:2 vci:2

*Jun 27 22:12:28.816: ATM2/0: Open_Channel(RSY): CH (1), VPI (2), VCI (2)

*Jun 27 22:12:28.816: ATM2/0: HI/LO watermarks: 526/263; PeakRate: 149760

*Jun 27 22:12:28.816: ATM2/0: Open_Channel(SEG): CH (1), VPI (2), VCI (2)

*Jun 27 22:12:28.820: ATM2/0: Setup_Cos: vc:3 wred_name:- max_q:0

The second example displays the commands sent to the SAR and the acknowledgements returned when
the VC is deleted and the segmentation and reassembly channels are closed:

Router(config-if)#

no pvc 2/2

Router(config-if)#

*Jun 27 22:12:59.016: ATM2/0: Sent pending EOP successfully

*Jun 27 22:12:59.016: ATM2/0: Close_Channel(RSY): Chan_ID (0x104)

*Jun 27 22:12:59.016: ATM2/0: Close_Channel(RSY): Chan_ID (0x104) CLOSE

*Jun 27 22:12:59.016: ATM2/0: Close_Channel: CLOSE_PENDING

*Jun 27 22:12:59.016: ATM2/0: Close_Channel(SEG): Chan_ID (0x105)

*Jun 27 22:12:59.016: ATM2/0: Close_Channel: CLOSE

Examples for the debug atm t3e3 trace command

The first example illustrates the output from the

debug atm t3e3 trace

command when it is run without

the

debug atm t3e3 sar

command being activated:

Router#

debug atm t3e3 trace

SAR CMD/ACK debugging is on

Router#

configure terminal

Router(config)#

interface atm 2/0

router(config-if)#

pvc 2/2

Router(config-if-atm-vc)#

exit

Router(config-if)#

*Jun 27 22:15:09.284: Command Sent:

*Jun 27 22:15:09.284: word 0: 0x00000480

*Jun 27 22:15:09.284: word 1: 0x00012010

*Jun 27 22:15:09.284: word 2: 0x00000000

*Jun 27 22:15:09.284: word 3: 0x00000000

*Jun 27 22:15:09.284: word 4: 0x00200020

*Jun 27 22:15:09.284: word 5: 0x00000000

*Jun 27 22:15:09.284: word 6: 0x00000000

*Jun 27 22:15:09.284: word 7: 0x00000000

*Jun 27 22:15:09.284: word 8: 0x00000000

*Jun 27 22:15:09.284: Command Indication:

*Jun 27 22:15:09.284: word 0: 0x00000000

*Jun 27 22:15:09.284: word 1: 0x01042110

*Jun 27 22:15:09.284: word 2: 0x01050000

*Jun 27 22:15:09.284: word 3: 0x0000003B

*Jun 27 22:15:09.284: ACK received = 200 usecs

*Jun 27 22:15:09.284: Command Sent:

*Jun 27 22:15:09.284: word 0: 0x01050480

*Jun 27 22:15:09.284: word 1: 0x00011010

*Jun 27 22:15:09.284: word 2: 0x02000000

*Jun 27 22:15:09.284: word 3: 0x00010003

*Jun 27 22:15:09.284: word 4: 0x00200020

*Jun 27 22:15:09.284: word 5: 0x64B30000

*Jun 27 22:15:09.284: word 6: 0x10C00000

*Jun 27 22:15:09.284: word 7: 0x86850000

*Jun 27 22:15:09.284: word 8: 0x00010040

*Jun 27 22:15:09.284: word 9: 0x00000000

*Jun 27 22:15:09.284: Command Indication:

*Jun 27 22:15:09.284: word 0: 0x00010000

*Jun 27 22:15:09.284: word 1: 0x00011110

*Jun 27 22:15:09.284: word 2: 0x02000000

*Jun 27 22:15:09.284: word 3: 0x0001003D

*Jun 27 22:15:09.284: ACK received = 200 usecs

Summary of Contents for NM-1A-E3



























Search results

Summary of Contents for NM-1A-E3

Reviews:

Related manuals for NM-1A-E3

Brands by name

Popular brands

Cisco NM-1A-E3, User Manual

Search results

Summary of Contents for NM-1A-E3

Reviews:

Related manuals for NM-1A-E3

Brands by name

Popular brands