manualshive.com logo in svg

Cypress CY8C28 series, Technical Reference Manual

The Cypress CY8C28 series, a versatile microcontroller range, boasts a comprehensive Technical Reference Manual. This invaluable manual can be downloaded for free, providing users with detailed insights and instructions for optimal product utilization. Visit our website 88.208.23.73:8080 to access this essential manual and unlock the full potential of your Cypress CY8C28 series.

Share
Download
background image

60

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

RAM Paging

4.2

Register Definitions

The following registers are associated with RAM Paging and are listed in address order. The register descriptions have an
associated register table showing the bit structure for that register. The bits in the tables that are grayed out are reserved bits
and are not detailed in the register descriptions that follow. Reserved bits should always be written with a value of ‘0’. For a
complete table of RAM Paging registers, refer to the 

“Summary Table of the Core Registers” on page 36

.

4.2.1

TMP_DRx Registers

The Temporary Data Registers (TMP_DR0, TMP_DR1,
TMP_DR2, and TMP_DR3) are used to enhance the perfor-
mance in multiple SRAM page PSoC devices.

These registers have no pre-defined function (for example,
the compiler and hardware do not use these registers) and
exist for the user to use as desired.

Bits 7 to 0: Data[7:0].  

Due to the paged SRAM architec-

ture of PSoC devices with more than 256 bytes of SRAM, a
value in SRAM may not always be accessible without first

changing the current page. The TMP_DRx registers are
readable and writeable registers that are provided to
improve the performance of multiple SRAM page PSoC
devices, by supplying some register space for data that is
always accessible.

For an expanded listing of the TMP_DRx registers, refer to
the 

“Summary Table of the Core Registers” on page 36

. For

additional information, refer to the 

TMP_DRx register on

page 155

.

4.2.2

CUR_PP Register

The Current Page Pointer Register (CUR_PP) is used to set
the effective SRAM page for normal memory accesses in a
multi-SRAM page PSoC device.

Bits 2 to 0: Page Bits[2:0].  

These bits affect the SRAM

page that is accessed by an instruction when the
CPU_F[7:0] bits have a value of either 10b or 11b. Source
indexed and destination indexed addressing modes, as well
as stack instructions, are never affected by the value of the
CUR_PP register. (See the STK_PP and IDX_PP registers
for more information.)

The source indirect post increment and destination indirect
post increment addressing modes, better know as MVI, are
only partially affected by the value of the CUR_PP register.
For MVI instructions, the pointer address is in the SRAM
page indicated by CUR_PP, but the address pointed to may
be in another SRAM page. See the MVR_PP and MVW_PP
register descriptions for more information. 

For additional information, refer to the 

CUR_PP register on

page 189

.

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

x,6xh

TMP_DRx

Data[7:0]

RW : 00

LEGEND

x

An ‘x’ before the comma in the address field indicates that this register can be read or written to no matter what bank is used. An “x” after the comma in the
address field indicates that there are multiple instances of the register. 

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Access

0,D0h

CUR_PP

Page Bits[2:0]

RW : 00

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Badger Meter PC100 Installation And Operation Manual preview
PC100
Brand: Badger Meter Pages: 20
Gardena 4030 Operating Instructions Manual preview
4030
Brand: Gardena Pages: 17
Badger Meter CB-30 User Manual preview
CB-30
Brand: Badger Meter Pages: 16
Federal Signal Corporation ultravoice UV Installation, Operation And Service Manual preview
ultravoice UV
Brand: Federal Signal Corporation Pages: 79
Federal Signal Corporation PAGASYS GEN II Description, Installation, And User Manual preview
PAGASYS GEN II
Brand: Federal Signal Corporation Pages: 32
Lattice LatticeMico8 User Manual preview
LatticeMico8
Brand: Lattice Pages: 23
MAKOT UMS-02 Manual preview
UMS-02
Brand: MAKOT Pages: 6
KaMo Pearldex Series Manual preview
Pearldex Series
Brand: KaMo Pages: 2
Olsen 58468 Owner'S Manual & Safety Instructions preview
58468
Brand: Olsen Pages: 4
Vectornav VN-200 Quick Start Manual preview
VN-200
Brand: Vectornav Pages: 18
IFM DX2011 Manual preview
DX2011
Brand: IFM Pages: 3
Brooks 5851EM Series Installation And Operation Manual preview
5851EM Series
Brand: Brooks Pages: 62
Intel MCS 51 User Manual preview
MCS 51
Brand: Intel Pages: 334
JR XP662 Instruction Manual preview
XP662
Brand: JR Pages: 88
Infineon Technologies XE166 Hardware Manual preview
XE166
Brand: Infineon Technologies Pages: 28
Knoll VC100SS Installation Manual preview
VC100SS
Brand: Knoll Pages: 1
MDT Technologies JAL-01UP.02 Technical Manual preview
JAL-01UP.02
Brand: MDT Technologies Pages: 84
YASKAWA MP2100 Series User Manual preview
MP2100 Series
Brand: YASKAWA Pages: 455

Brands by name

Popular brands

Load more brands