36
P0016-LI-02.01
5 Test/Misc.
On: The selected ARC reports events that are assigned in the
test/misc. group.
Off: The selected ARC does not report test/misc. events.
6 Restore
On: The selected ARC reports events that are assigned in the
restore group.
Off: The selected ARC does not report restore events.
7 Custom
On: The selected ARC reports events that are assigned in the
custom group.
Off: The selected ARC does not report custom events.
ARC 1-4: Cancel on Success
This set of options allows you to control communication sequence
for each ARC. When the on-board communicator is triggered by an
event it will call the ARC using the settings defined in ARC 1. If the
communication attempt is successful, this option can be used to
either cancel attempts for the remaining available ARC’s or move
on and call the next available ARC.
Locations:
7061
to
7064
ARC 1 to 4: Cancel on Success.
Entry Mode:
Bit Toggle Selection (see page 17).
1
Stop ARC 1
On: The selected ARC will cancel further attempts to ARC 1 after
a successful communication.
Off: The selected ARC will move on to next ARC after a successful
communication.
2
Stop ARC 2
On: The selected ARC will cancel further attempts to ARC 2 after
a successful communication.
Off: The selected ARC will move on to next ARC after a successful
communication.
3
Stop ARC 3
On: The selected ARC will cancel further attempts to ARC 3 after
a successful communication.
Off: The selected ARC will move on to next ARC after a successful
communication.
4
Stop ARC 4
On: The selected ARC will cancel further attempts to ARC 4 after
a successful communication.
Off: The selected ARC will move on to next ARC after a successful
communication.
ARC 1-4: IP Address
This option allows an IP address to be programmed for each ARC.
Locations:
7081
to
7084
ARC 1 to 4: IP Address.
Entry Mode:
String Edit - Number Mode (see page 18).
Whilst programming IP address, addition characters can be
inserted:
B3
: Insert a “.”.
ARC 1-4: IP Port Number
This option allows an IP port number to be programmed for each
ARC.
Locations:
7091
to
7094
ARC 1 to 4: IP Port Number.
Entry Mode:
String Edit - Number Mode (see page 18).
Options: Auto Test Call Period
The on-board communicator can be programmed to send a test
call event to the ARC. This option controls the period in hours in
which a test call is sent. The test call timer is reset every time a
system event is successfully communicated, therefore a test call
will only be sent once the timer reaches zero.
Location:
7101
Entry Mode:
Number Entry (see page 18).
Options: Auto Test Call Time
This option allows you to program a time at which the on-board
communicator sends a test call.
Location:
7102
Entry Mode:
Number Entry (see page 18).
The time must be entered in a 24hr format, e.g., 2100 = 9:00PM.
To disable this feature program the time as 0000.
Options: Auto Test Days
This option allows you to select which days of the week the on-
board communicator sends a test call.
Location:
7103
Entry Mode:
Bit Toggle Selection (see page 17).
Options 1 to 7 = Sunday to Saturday.
Options: PSTN Pre-Dial Number
This option allows a PSTN pre-dial number (up to 3 digits) to be
programmed. Most internal telephone systems require a digit to
be dialled before an outside line and dial tone is made available.
If this feature is required, make sure that the “Use PSTN Pre-Dial”
option is enabled for the required ARC, see “Protocol Options” on
page 35.
Location:
7104
Entry Mode:
String Edit - Number Mode (see page 18).
Fast Format: Reporting Channels
When the ARC protocol is programmed as Fast Format, the
channels that are used for reporting must be enabled or disabled.
Locations:
7201
- Reporting Channels 1 – 8.
7241
- Reporting Channels 9 – 16.
Entry Mode:
Bit Toggle Selection (see page 17).
1
Report Channel 1/9
On: For location 7201 channel 1 is enabled, for location 7241
channel 9 is enabled.
Off: For location 7201 channel 1 is disabled, for location 7241
channel 9 is disabled.
2
Report Channel 2/10
On: For location 7201 channel 2 is enabled, for location 7241
channel 10 is enabled.
Off: For location 7201 channel 2 is disabled, for location 7241
channel 10 is disabled.
3
Report Channel 3/11
On: For location 7201 channel 3 is enabled, for location 7241
channel 11 is enabled.
Off: For location 7201 channel 3 is disabled, for location 7241
channel 11 is disabled.
