manualshive.com logo in svg

Freescale Semiconductor MPC5632M, Manual

The Freescale Semiconductor MPC5632M is a cutting-edge microcontroller designed for a wide range of applications. With its advanced features and high performance, this product is perfect for professionals and enthusiasts alike. Discover its full potential by downloading the user manual for free from our website.

Share
Download
background image

MPC563XM Reference Manual, Rev. 1

Freescale Semiconductor

415

 

Preliminary—Subject to Change Without Notice

14.3.1.2

Hardware Vector Mode

In hardware vector mode, the hardware is the interrupt vector signal from the INTC in conjunction with a 
processor with the capability to use that vector. In hardware vector mode, this hardware causes the first 
instruction to be executed in handling the interrupt request to the processor to be specific to that vector. 
Therefore the interrupt exception handler is specific to a peripheral or software setable interrupt request 
rather than being common to all of them. The INTC will use hardware vector mode for a given processor 
when its associated the HVEN_PRC0 or HVEN_PRC1 bit in the INTC_BCR is asserted. The hardware 
vector enable signal to the associated processor is driven as asserted. When the interrupt request to the 
associated processor asserts, the interrupt vector signal is updated. The value of that interrupt vector is the 
unique vector associated with the preempting peripheral or software setable interrupt request. The vector 
value matches the value of the INTVEC_PRC0 field in the INTC_IACKR_PRC0 or the INTVEC_PRC1 
field in the INTC_IACKR_PRC1, depending on which processor was assigned to handle a given interrupt 
source.

The processor negates the interrupt request to the processor driven by the INTC by asserting the interrupt 
acknowledge signal for one clock. Even if a higher priority interrupt request arrived while waiting for this 
interrupt acknowledge, the interrupt request to the processor will negate for at least one clock.

The assertion of the interrupt acknowledge signal for a given processor pushes the associated PRI value in 
the associated INTC_CPR_PRC

x

 register onto the associated LIFO and updates the associated PRI in the 

associated INTC_CPR_PRC

x

 register with the new priority. This pushing of the PRI value onto the 

associated LIFO and updating PRI in the associated INTC_CPR_PRC

x

 does not occur when the associated 

interrupt acknowledge signal asserts and the 

Section 14.5.10, “INTC Software Set/Clear Interrupt 

Registers (INTC_SSCIR0_3 - INTC_SSCIR4_7)

” is written at a time such that the PRI value in the 

associated INTC_CPR_PRC

x

 register would need to be pushed and the previously last pushed PRI value 

would need to be popped simultaneously. In this case, PRI in the associated INTC_CPR_PRC

x

 is updated 

with the new priority, and the associated LIFO is neither pushed or popped.

14.3.2

Debug Mode

The INTC operation in debug mode is identical to its operation in normal mode.

14.3.3

Stop Mode

The INTC supports the stop mode mechanism. The INTC can have its clock input disabled at any time by 
the clock driver on the SoC. While its clocks are disabled, the INTC registers are not accessible.

Some SoC applications require that any peripheral interrupt request source be able to awaken a portion or 
all of the SoC from stop mode. Since the INTC requires clocking in order for a peripheral interrupt request 
to generate an interrupt request to the processor, it does not support that requirement if it is not clocked.

14.3.4

Factory Test Mode

All INTC registers are accessible in factory test mode.

Summary of Contents for MPC5632M









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5632M

Paoli F1 Operating And Maintenance Manual preview
F1
Brand: Paoli Pages: 16
Samson 3277 Mounting And Operating Instructions preview
3277
Brand: Samson Pages: 48
L-Acoustics LA4X Maintenance Manual preview
LA4X
Brand: L-Acoustics Pages: 24
L-Acoustics LA8 Maintenance Manual preview
LA8
Brand: L-Acoustics Pages: 21
Eaton CDAU-01/04 Instruction Leaflet preview
CDAU-01/04
Brand: Eaton Pages: 4
XtendLan KEYBPTZ4D Operating Instructions Manual preview
KEYBPTZ4D
Brand: XtendLan Pages: 12
Reer MOSAIC MA2 Quick Installation Manual preview
MOSAIC MA2
Brand: Reer Pages: 2
ICP DAS USA ALM-04-MRTU User Manual preview
ALM-04-MRTU
Brand: ICP DAS USA Pages: 26
National Instruments cRIO-FRC II User Manual And Specifications preview
cRIO-FRC II
Brand: National Instruments Pages: 22
Virtualfly TQ6+ User Manual preview
TQ6+
Brand: Virtualfly Pages: 5
Braun Group ES-SVC Series User Manual preview
ES-SVC Series
Brand: Braun Group Pages: 15
Mircom RB-MD-1086 Series Installation Instructions preview
RB-MD-1086 Series
Brand: Mircom Pages: 4
Genesys Irid 400 RGB Instructions Of Use preview
Irid 400 RGB
Brand: Genesys Pages: 23
Daitsu SPACE V4 Series User Manual preview
SPACE V4 Series
Brand: Daitsu Pages: 29
Daitsu WWP V2 Operation Manual preview
WWP V2
Brand: Daitsu Pages: 4
Frigidaire GLEB30T9FB - 30" Electric Double Wall Oven Install Manual preview
GLEB30T9FB - 30" Electric Double Wall Oven
Brand: Frigidaire Pages: 29
Chamberlain 872 Series User Manual preview
872 Series
Brand: Chamberlain Pages: 2
Zennio Tecla XL X10 User Manual preview
Tecla XL X10
Brand: Zennio Pages: 19

Brands by name

Popular brands

Load more brands