Freescale Semiconductor PXR4030 Reference Manual Download | Manualshive

Page: 1180 / 1434

background image

Enhanced Time Processing Unit (eTPU2)

29-12

Freescale Semiconductor

PXR40 Microcontroller Reference Manual, Rev. 1

User has the ability to program the eTPU Cores with User Time Functions, having access to the
Shared Code Memory (SCM).

•

User Mode

User does not access the eTPU Shared Code Memory:

— Use of predefined eTPU Functions

— No need for eTPU Core programming ability

•

Debug Mode

User debugs eTPU code, accessing special Trace/Debug features via Nexus interface:

— hardware breakpoint/watchpoint setting

— access to internal registers

— single-step execution

— forced instruction execution

— software breakpoint insertion and removal.

•

Module Disable Mode

eTPU Engine clocks are stopped through a register write to ETPUECR bit MDIS, saving power.
Input sampling stops. eTPU Engines can be in Module Disable Mode independently. Module
Disable Mode stops only the Engine clock, so that the Shared BIU, and Global Channel registers
can be accessed, and interrupts and DMAs can be cleared and enabled/disabled. An Engine only
enters Module Disable Mode when any currently running thread is finished. Refer to the

eTPU

Reference Manual

for details.

•

Stop Mode

Stop Mode is entered when eTPU answers device stop request assertion with stop acknowledge.
Refer to the SIU_HLT and SIU_HLTACK register descriptions for details on how to place this
module in Stop mode.

These modes are loosely selected: there is no unique register field or signals to choose between them.
Some features of one mode can be used with features of other mode(s). More on this subject can be found
on

Section 29.1.3.1, eTPU Mode Selection,

below.

NOTE

Throughout this document, an engine is said to be “stopped” if it is either in
Module Disable mode or Stop mode.

29.1.3.1

eTPU Mode Selection

User and User Configuration are the normal operating modes, and differ from each other only in access to
SCM. User programmability is only possible with a RAM SCM.

Debug Mode is characterized by the use of the debug interface features. Specifically, Nexus blocks provide
Nexus class 3 debug features. For more information on debug features, refer to the

eTPU Reference

Manual

.

«
...
1178
1179
1180
1181
1182
...
»

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXR4030

Brand: Hanbay Pages: 18

Brand: GCE Pages: 24

Brand: Hach Pages: 36

Brand: Lawler Pages: 5

Brand: National Instruments Pages: 14

Brand: National Instruments Pages: 20

Brand: Rain Bird Pages: 138

FUTERA XLF Series

Brand: RBI Pages: 128

Brand: RBH Access Technologies Pages: 36

Brand: S&C Pages: 11

Brand: S&C Pages: 24

Brand: S&C Pages: 19

CEmarking RCX221

Brand: Yamaha Pages: 468

Brand: Abov Pages: 138

SaunaLogic SL2 Control

Brand: Finnleo Pages: 14

Clip Studio TABMATE

Brand: CELSYS Pages: 2

MIMIC HRNDWHEELS

Brand: MRMC Pages: 20

Brand: Cypress Pages: 571

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands