Freescale Semiconductor PXR4030 Reference Manual Download | Manualshive

Page: 891 / 1434

background image

Deserial Serial Peripheral Interface (DSPI)

Freescale Semiconductor

25-31

PXR40 Microcontroller Reference Manual, Rev. 1

25.4

Functional Description

The Deserial Serial Peripheral Interface (DSPI) block supports full-duplex, synchronous serial
communications between MCUs and peripheral devices. The DSPI can also be used to reduce the number
of pins required for I/O by serializing and deserializing up to 16 Parallel Input/Output signals. All

Table 25-25. DSPI_SDR Field Descriptions

Field Description

0–2

Reserved, should be cleared.

3–7

TSBCNT

Timed Serial Bus Operation Count. When TSBC is set, TSBCNT defines the length of the TSB frame.
A number between 4 and 32.
The TSBCNT field selects number of bits to be shifted out during a transfer in TSB Operation. The
field sets the number of SCK cycles that the bus Master will generate to complete the transfer. The
number of SCK cycles used will be one more than the value in the TSBCNT field. The number of SCK
cycles defined by TSBCNT must be equal to or greater than the frame size.

8–13

Reserved, should be cleared.

14

DSE1

Data Select Enable1. When TBSC bit is set, the DSE1 bit controls insertion of the zero bit (Data
Select) in the middle of the data frame. The insertion bit position is defined by FMSZ field of
DSPI_CTARn register, selected by DSICTAS field of the DSPI_DSICR register.
0 No Zero bit inserted in the middle of the data frame.
1 Zero bit is inserted at the middle of the data frame. Total number of bits in the data frame is

increased by 1.

15

DSE0

Data Select Enable0. When TBSC bit is set, the DSE0 bit controls insertion of the zero bit (Data
Select) in the beginning of the data frame.
0 No Zero bit inserted in the beginning of the frame
1 Zero bit is inserted at the beginning of the data frame. Total number of bits in the data frame is

increased by 1.

16–23

Reserved, should be cleared.

24–31

DPCS1_x

DSI Peripheral Chip Select 0–7. These bits define the CS to assert for the second part of the DSI
frame when operating in TSB configuration with dual receiver. The DPCS1 bits select which of the
PCS signals to assert during the second DSI transfer. The DPCS1 bits only control the assertions of
the PCS signals in DSI Master Mode when in TSB configuration.
0 Negate PCS[x]
1 Assert PCS[x]

TSBCNT

Framesize

00000

Reserved

00001

Reserved

00010

Reserved

00011

4

00100

5

00101

6

...

...

11111

32

«
...
889
890
891
892
893
...
»

Summary of Contents for PXR4030



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for PXR4030

Brand: Bartlett Pages: 30

Brand: Bard Pages: 8

Brand: ZKTeco Pages: 8

Brand: EasyIO Pages: 18

Brand: Salda Pages: 16

Brand: Warren Controls Pages: 28

Brand: EAS Electric Pages: 89

Brand: WAGO Pages: 414

Brand: V2 Pages: 48

CEmarking RCX221

Brand: Yamaha Pages: 468

Brand: fadini Pages: 28

Brand: Pangolin Pages: 35

Brand: IDTECK Pages: 51

CIMR-VC*****H**-00 series

Brand: YASKAWA Pages: 32

StarSign Bio Token 3.0 M

Brand: Giesecke & Devrient Pages: 28

Brand: Melexis Pages: 13

Brand: Doepke Pages: 2

Brand: Linear Technology Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands