IFM CR3132 Operating Instructions Manual Download

Page: 19 / 22

CANwireless

CR3132

Object

Index

Subindex

Data type

Configuration

Server Type

0x3010

0x18

Unsigned 16

30000 (default)

Tab. 6: WLAN server (Mini Access Point)

Object

Index

Subindex

Data type

Configuration

WLAN Enable

0x3008

0x02

Unsigned 8

1: switch on

Bluetooth Enable

0x3008

0x03

Unsigned 8

0: switch off

WLAN Operating Mode

0x3000

0x01

Unsigned 8

1: infrastructure

SSID

0x3000

0x02

Visible_string

Enter the SSID of the WLAN network

Authentication Type

0x3000

0x04

Unsigned 8

7: WPA/WPA2 Mixed

Authentication Key

0x3000

0x05

Visible_String

Enter the authentication key of the
WLAN network

DHCP

0x3000

0x09

Unsigned 8

1: client

(only for WLAN infrastructure)

Hostname

0x3005

0x01

Visible_string

Enter a unique device name

Connection Command
1

0x3010

0x01

Unsigned 8

2: connect with static address

Client Enable

0x3010

0x15

Unsigned 8

3: turn on client

Server Type

0x3010

0x16

Unsigned 8

1: socket (TCP/UDP)

Server Type

0x3010

0x18

Unsigned 16

30000 (default)

EEP URL Address/
WLAN Client only 1

0x3010

0x17

Visible_string

Enter the IP address of the WLAN
MiniAP

Tab. 7: WLAN client (infrastructure)

8.3.10 CAN - Mobile device / PC interface P2P WLAN Mini Access Point

In this mode, a wireless connection is established between a CANwireless device and any other
WLAN-enabled device via WLAN. The CANwireless device needs to be configured as follows:

Object

Index

Subindex

Data type

Configuration

WLAN Enable

0x3008

0x02

Unsigned 8

1: switch on

Bluetooth Enable

0x3008

0x03

Unsigned 8

0: switch off

WLAN Operating Mode

0x3000

0x01

Unsigned 8

2: Mini Access Point (default)

SSID

0x3000

0x02

Visible_string

Enter a unique name for the WLAN
network

Authentication Type

0x3000

0x04

Unsigned 8

7: WPA/WPA2 Mixed

Authentication Key

0x3000

0x05

Visible_String

Enter a secure authentication key with
at least 8 characters

DHCP

0x3000

0x09

Unsigned 8

2: server (default)

(only for WLAN MiniAP)

Hostname

0x3005

0x01

Visible_string

Enter a unique device name

IP address

0x3000

0x0a

Visible_string

192.168.0.34

Network mask

0x3000

0x0b

Visible_string

255.255.255.0

Gateway address

0x3000

0x0c

Visible_string

192.168.0.1

Primary DNS Server

0x3000

0x0d

Visible_string

192.168.0.1

Secondary DNS Server

0x3000

0x0e

Visible_string

192.168.0.2

Connection Command
1

0x3010

0x01

Unsigned 8

0: default

Server Enable

0x3010

0x15

Unsigned 8

2: turn on server

Server Type

0x3010

0x16

Unsigned 8

1: socket (TCP/UDP)

Summary of Contents for CR3132























Search results

Summary of Contents for CR3132

Reviews:

Related manuals for CR3132

Brands by name

Popular brands

IFM CR3132, Operating Instructions Manual

Search results

Summary of Contents for CR3132

Reviews:

Related manuals for CR3132

Brands by name

Popular brands