Keba ServoOne Device Help Download

Page: 269 / 493

Control mode

NOTE

“Control mode” does

not

refer to the motor control here (see

Section "Control" on page 110), but rather to the source that will
specify the table index!

P 205[0] - MPRO_TAB_Mode is used to define which source will specify the table

index:

PARA (0) = via current index (parameter no. 207)

The value written to P 207[0] - MPRO_TAB_ActIdx (via a fieldbus, for

example) will immediately be applied as the current table index and the

corresponding driving job will be carried out.

TERM (1) = via terminals

A bit pattern that will be applied as the value for the table index will be

specified via digital inputs. In order to be able to select all 16 table entries,

four digital inputs with TAB0(23) = Binary table index 2^0 to TAB3(26) =

Binary table index 2^3 need to be configured. For details on configuring the

digital inputs, see Section "Digital inputs" on page 303.

AUTO (2) = via time delay (parameter no. 204)

Automatic processing of follow-up driving jobs. The number of driving jobs

entered in parameter P 206[0] - MPRO_Tab_MaxIdx is processed in

sequence. This operation is repeated until the drive is stopped or the table is

disabled. There will be a wait time of P 204 - MPRO_TAB_WaitTime

between the individual driving jobs.

BUS (3) = via fieldbus

Selection of a table value via PROFIBUS. No other field bus systems are

implemented. For details on PROFIBUS, see Section "PROFIBUS /

PROFINET" on page 457.

ID No.: 0842.26B.5-01 Date: 09.2020

ServoOne - Device Help

269

8 Motion profile

AUTO_COMPLETE (4) = via auto complete mode (parameter no. 204)

As with "AUTO (2)", as long as the input is set, the table will be executed.

After being deactivated, the entire table will be run through to the end once

more.

Reference

With ...

P 195 - MPRO_TAB_TRef

(for torque control) or

P 198 - MPRO_TAB_SRef

(for speed control) or

P 202 - MPRO_TAB_PRef

(for position control)

and indexes 0–15, the setpoint for each individual motion task can be defined.

In "Infinite positioning" mode the speed can be specified signed. It is limited by P 328

[0] - CON_SCON_SMax (for details, see Section "Speed- / velocity limits" on page

326).

Mode

If the Servo controller is run with motor control mode "PCON(3) = Position control

mode" (for information on the setting, see Section "Basic settings" on page 112), the

“Mode” and “Speed” lines will be added to the “Setpoint table” screen.

Summary of Contents for ServoOne














































































































































































































































































































































































































































































































Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands

Keba ServoOne, Device Help

Search results

Summary of Contents for ServoOne

Reviews:

Related manuals for ServoOne

Brands by name

Popular brands