background image

 

 

 

 

  

Linux 5.10 Yocto SDK 

V2.1 

24/25 

 

© MicroSys Electronics GmbH 2022 

 

 

 

 

7.4 

Glossary 

Here are some acronyms and abbreviations which you will encounter when dealing 
with the SDK and NXP's Layerscape processors.  
 

ATF 

Arm Trusted Firmware. Now more accurately known as TF-A 
(Trusted Firmware-A). See 

https://developer.arm.com/

  

DPAA 

Data Path Acceleration Architecture (first generation) used in 
LS1043A and LS1046A 

DPAA2 

Data Path Acceleration Architecture (second generation) used in 
LS1088A and LX2160A 

DPC 

Data Path Configuration file. Needed for DPAA2 

DPL 

Data Path Layout. Needed for DPAA2 

DTB 

Device Tree Blob. The binary representation of device trees. 

FMan 

Frame Manager. A DPAA hardware block. 

FSL 

Freescale (were acquired by NXP Semiconductors in Dec 2015) 

ITB 

Image Tree Binary. A file containing kernel(s) and device tree(s) 

MC 

Management Complex. A DPAA2 hardware block. 

PBL 

Pre-Boot Loader. Can be optionally loaded after RCW. 

PPA 

Primary Protected Application. A secure monitor running in 
TrustZone which provides boot and runtime software services such 
as PSCI and Arm

’s SMC calling convention. 

PSCI 

Power State Coordination Interface. An Arm standard interface. 

RCW 

Reset Configuration Word. The first data the processor loads to 
configure various interfaces and internal frequencies. 

 

 
 
 
 
 
 
 

Summary of Contents for Linux 5.10 Yocto SDK


























Reviews: