Nice PP7124, Instructions And Warnings For Installation And Use

ENGLISH – 

17

7.3  LEVEL 2 PROGRAMMING (ADJUSTABLE PARAMETERS)

All the Level 2 parameters are factory-set as highlighted in “

GREY

” in “

Table 6

” and can be modified at any time. The parameters 

can be set to a scale of 1 to 8. The check the value corresponding to each LED, refer to “

Table 6

”.

7.3.1 Level 2 programming procedure

m 

The user has maximum 10 seconds to press the buttons consecutively during the programming procedure, 

after which time the procedure terminates automatically and memorises the changes made up to then.

To perform Level 2 programming:

1. 

press and hold the 

g

 button until LED “

L1

” starts flashing

2. 

release the 

g

 button when LED “

L1

” starts flashing

3. 

press the 

f

 or 

h

 button to move the flashing LED to the “

entry LED

” associated with the parameter to be 

modified

4. 

press and hold the 

g

 button. With the 

g

 button pressed:

–

wait roughly 3 seconds, until the LED representing the current level of the parameter to be modified lights up

–

press the 

f

 or 

h

 button to shift the LED associated with the parameter’s value

5. 

release the 

g

 button

6. 

wait 10 seconds (maximum time) to exit the programming mode.

l 

To set multiple parameters during the procedure's execution, repeat the operations from point 2 to point 4 dur-

ing the phase itself.

l 

The set value highlighted in grey (“Table 6”) indicates that this value is the factory setting.

Table 6

LEVEL 2 FUNCTIONS (ADJUSTABLE PARAMETERS)

Entry 

LED

Parameter

LED 

(level)

Set value

Description

L1

Pause Time

L1

5 seconds

Adjusts the pause time, 

i.e. the time before 

automatic re-closure. 

Is effective only if 

“Automatic Closing” is 

enabled.

L2

15 seconds

L3

30 seconds

L4

45 seconds

L5

60 seconds

L6

80 seconds

L7

120 seconds

L8

180 seconds

L2

Step-by-Step 

function

L1

Open - Stop - Close - Stop

Controls the sequence of 

commands associated 

with the “SbS”, “Open” 

and “Close” inputs or the 

radio control.

[

Note :

] by setting L4, 

L5, L7 and L8, also the 

behaviour of the “Open” 

and “Close” commands 

is modified.

L2

Open - Stop - Close - Open

L3

Open - Close - Open - Close

L4

Condominium: during the 

opening manoeuvre

 the “Step-by-Step” and 

“Open” commands do not cause any effect, while the “Close” command 

causes the movement to reverse, namely closing of the leaves; during 

the 

closing manoeuvre

 the “Step-by-Step” and “Open” commands 

cause the movement to reverse, namely opening of the leaves, while the 

“Close” command does not cause any effect.

L5

Condominium 2: during the 

opening manoeuvre

 the “Step-by-Step” 

and “Open” commands do not cause any effect, while the “Close” 

command causes the movement to reverse, namely closing of the gate 

leaves. If the sent command remains for more than 2 seconds, a “Stop” 

command is executed. During the 

closing manoeuvre

 the “Step-by-

Step” and “Open” commands cause the movement to reverse, namely 

opening of the leaves, while the “Close” command does not cause any 

effect. If the sent command remains for more than 2 seconds, a “Stop” 

command is executed.

L6

Step-by-Step 2 (less than 2 sec triggers “Partial Open”)

L7

Hold-to-run: the manoeuvre is only executed if the sent command 

remains; if it is interrupted, the manoeuvre stops.

L8

Opening in “semi-automatic” mode, closing in “hold-to-run” mode

L3

Motor speed

L1

Very slow

Adjusts the motor 

speed during normal 

manoeuvres.

L2

Slow

L3

Medium

L4

Fast

L5

Very fast

L6

Extremely fast

L7

Opens “Fast”; closes “Slow”

L8

Opens “Extremely fast”; closes “Medium”