Esprit 728 Ultra & 738 Ultra
13
4.2.2
Hex Streamlined Section Programming
This is an alternate method to Hex Programming. The addresses (000 to 043 and 300 to 527) programmed in the Hex
Programming method are grouped into 68 sections where each section contains four addresses (i.e. section 00 =
addresses 000 to 003). Using this method allows you to program 8 digits (4 addresses) without having to exit and re-
enter addresses. When entering the final digit, the software will automatically advance to the next section.
Example: If you complete the 728 Ultra & 738 Ultra System Programming Guide with the desired data, you can
program the 68 sections by entering all of the digits without pressing
[
ENTER
]
or entering any other addresses. This
greatly reduces programming time.
The keypad will not display the current data in the Hex Streamlined Programming method.
To program using the Hex Streamlined Section method:
1. Press
[
ENTER
]
+ Installer code +
[7]
. The
[
ENTER
]
and
[2
ND
]
keys will flash to indicate you are in streamlined
programming mode (LED keypad only).
2. Enter 2-digit section (00 to 67). The
[
ENTER
]
key will remain on and the
[2
ND
]
key will turn off (LED keypad only).
3. Enter 8-digit data to program the section. The keypad will beep to indicate that the section has been programmed,
data is saved and the software has advanced to the next section.
4. Return to step 3 to continue programming or press
[
CLEAR
]
to exit programming mode.
4.2.3
Decimal Programming
Addresses 044 to 061 are programmed
using the Decimal Programming method.
Values entered must contain three digits
from 000 to 255. To program using the
Decimal Programming method:
1. Press
[
ENTER
]
+ Installer code. The
[
ENTER
]
key will flash to indicate you
are in programming mode (LED keypad
only).
2. Enter 3-digit address (044 to 061). The
keypad will now display the current 3-
digit data currently saved at this
address as described in Figure 24.
3. Enter 3-digit data (decimal) value. After
entering data you do not need to press
[
ENTER
]
, the software will automatically
save the data into the selected
address.
4. Return to step 2 to continue
programming or press
[
CLEAR
]
to exit
programming mode.
4.2.4
Feature Select Programming
Addresses 062 to 126 are programmed using the Feature Select Programming method. In this method, every key in
each address on the keypad represents an option or feature. Pressing a key will display it on the keypad and pressing
it again will extinguish the key. The ON/OFF status of each key determines the selected feature. To program using the
Feature Select Programming method:
1. Press
[
ENTER
]
+ Installer code. The
[
ENTER
]
key will flash to indicate you are in programming mode.
2. Enter 3-digit address (062 to 126). After entering the address, the keypad will display the feature selection status.
The ON/OFF status of the keys determines the selected features as described in the
728 Ultra & 738 Ultra System
Programming Guide
and in the appropriate sections of this manual. Turn the keys ON/OFF by pressing the
appropriate key until the desired options are set. Then press the
[
ENTER
]
key to accept, there will be a confirmation
beep indicating the options have been accepted. The
[
ENTER
]
key will flash to indicate that the software is awaiting
the next address entry (LED keypad only).
3. Return to step 2 to continue programming or press
[
CLEAR
]
to exit programming mode.
Figure 24: Decimal Display For LED Keypads
Note: LCD keypads will display current data on the screen.
Each key in the first 2 rows of the keypad represents a specific value when the key is lit, as
shown above. When the key isn’t lit, the key represents 0. Add the values of the lit keys to
obtain the entered data value as shown in the example below.
Example
Therefore 8 + 1 + 32 +16 = 057
Summary of Contents for ESPRIT 728 ULT
Page 1: ...Versions 4 4 728ULT 4 1 738ULT Reference Installation Manual 728ULT 738ULT ...
Page 2: ......
Page 54: ...Notes ...
Page 55: ......
