manualshive.com logo in svg

Freescale Semiconductor MPC5553, Reference Manual

The Freescale Semiconductor MPC5553 is a powerful microcontroller designed for automotive and industrial applications. For detailed information on how to use this product, download the Reference Manual for free from 88.208.23.73:8080. This manual provides all the necessary information to optimize the performance of your MPC5553.

Share
Download
background image

MPC5553/MPC5554 Microcontroller Reference Manual, Rev. 5

19-74

Freescale Semiconductor

 

NOTE

An asserted EOQF

n

 only implies that the eQADC has finished transferring

a command with an asserted EOQ bit from CFIFO

n

. It does not imply that

result data for the current command and for all previously transferred
commands has been returned to the appropriate RFIFO.

19.4.3.6.3

Pause Status

In edge trigger mode, when the eQADC completes the transfer of a CFIFO entry with an asserted pause
bit, the eQADC will stop future command transfers from the CFIFO and set EQADC_FISRn[PF] (see
Section 19.3.2.8). Refer to 

Section 19.4.1.2, “Message Format in eQADC

,” for information on command

message formats. The eQADC ignores the pause bit in command messages in any software level trigger
mode. The eQADC sets the PF flag upon detection of an asserted pause bit only in single or
continuous-scan edge trigger mode. When the PF flag is set for a CFIFO in single-scan edge trigger mode,
the EQADC_FISRn[SSS] bit will not be cleared (see Section 19.3.2.8).

In level trigger mode, the definition of the PF flag has been redefined. In level trigger mode, when CFIFO

n

is in TRIGGERED status, PF

n

 is set when the CFIFO status changes from TRIGGERED due to detection

of a closed gate. The pause flag interrupt routine can be used to verify if the a complete scan of the
command queue was performed. If a closed gate is detected while no command transfers are taking place,
it will have immediate effect on the CFIFO status. If a closed gate is detected during the serial transmission
of a command to the external device, it will have no effect on the CFIFO status until the transmission
completes. 

When EQADC_CFCR[PIE] (see Section 19.3.2.6) and EQADC_FISRn[PF] are asserted, the eQADC will
generate a pause interrupt request.

NOTE

In edge trigger mode, an asserted PF

n

 only implies that the eQADC finished

transferring a command with an asserted pause bit from CFIFO

n

. It does not

imply that result data for the current command and for all previously
transferred commands has been returned to the appropriate RFIFO.

NOTE

In software or level trigger mode, when the eQADC completes the transfer
of an entry from CFIFO

n

 with an asserted pause bit, PF

n

 will not be set and

command transfers will continues without pausing.

19.4.3.6.4

Trigger Overrun Status

When a CFIFO is configured for edge- or level-trigger mode and is in a TRIGGERED state, an additional
trigger occurring for the same CFIFO results in a trigger overrun. The trigger overrun bit for the
corresponding CFIFO will be set (EQADC_FISRn[TORF

n

] = 1, see Section 19.3.2.8). When

EQADC_CFCRn[TORIE] (see Section 19.3.2.6) and EQADC_FISRn[TORF] are asserted, the eQADC
generates a trigger overrun interrupt request.

For CFIFOs configured for level-trigger mode, a trigger overrun event is only detected when the gate
closes and reopens during a single serial command transmission as shown in 

Figure 19-40

.

Summary of Contents for MPC5553

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC5553

Eaton SC100 Operation Handbook preview
SC100
Brand: Eaton Pages: 86
Davey Torrium 2 TT45 Installation And Operating Instructions Manual preview
Torrium 2 TT45
Brand: Davey Pages: 12
YASKAWA Z1000 CIMR-ZU*A Series Programming Manual preview
Z1000 CIMR-ZU*A Series
Brand: YASKAWA Pages: 340
ETC Echoflex ELED2 Installation Manual preview
Echoflex ELED2
Brand: ETC Pages: 8
Texas Instruments MSP430F67681 Manual preview
MSP430F67681
Brand: Texas Instruments Pages: 27
CELSYS Clip Studio TABMATE Instructions preview
Clip Studio TABMATE
Brand: CELSYS Pages: 2
MRMC MIMIC HRNDWHEELS Quick Start Manual preview
MIMIC HRNDWHEELS
Brand: MRMC Pages: 20
Atari IDEa How To Connect preview
IDEa
Brand: Atari Pages: 3
Dungs 273061 Instructions Manual preview
273061
Brand: Dungs Pages: 56
Emec PH CONTROLLER Operating Manual preview
PH CONTROLLER
Brand: Emec Pages: 8
Ezodo 4801P Manual preview
4801P
Brand: Ezodo Pages: 7
Pangolin FB4 Series User Manual preview
FB4 Series
Brand: Pangolin Pages: 35
Ubiquiti UA-Hub Quick Start Manual preview
UA-Hub
Brand: Ubiquiti Pages: 16
Black Stone BL 981411-0 Instruction Manual preview
BL 981411-0
Brand: Black Stone Pages: 2
Lumel re72 series Quick Start Manual preview
re72 series
Brand: Lumel Pages: 32
Acard PCI-to-IDE ATA-133 User Manual preview
PCI-to-IDE ATA-133
Brand: Acard Pages: 33
GCE Druva MTLX Instructions For Use Manual preview
Druva MTLX
Brand: GCE Pages: 46
Tusa RS-790 Owner'S Manual preview
RS-790
Brand: Tusa Pages: 72

Brands by name

Popular brands

Load more brands