32
MU128 MIDI
[Note]
mm ll: 00 127
(=-87.5) cents is
followed by 01 00
(=-87.4) cents.
00
02
mm
--
Coarse tuning
mm: 40 - 64 - 88
(-24...0...+24 semitones)
127
127
--
--
RPN Null
This sets RPN and NRPN
numbers to an unset state.
Internal data is not affected.
*1 Refer to 1.2.4
*2 '--' indicates that the setting value is ignored.
1.2.23 Assignable controller
By assigning a control change number of 0...95 to a part,
the specified effect can be controlled.
This device allows two control change numbers (AC1 and
AC2) to be specified for each part.
The following parameters specify the effect of AC1 and AC2.
• Multi Part Parameter
1. AC1, AC2 PITCH CONTROL
2. AC1, AC2 FILTER CONTROL
3. AC1, AC2 AMPLITUDE CONTROL
4. AC1, AC2 LFO PMOD DEPTH
5. AC1, AC2 LFO FMOD DEPTH
6. AC1, AC2 LFO AMOD DEPTH
• Effect1 Parameter
7. AC1, AC2 VARIATION CONTROL DEPTH
(Valid if Variation Effect is assigned to a part as Insertion)
• Effect 2 Parameter
8. AC1, AC2 INSERTION CONTROL DEPTH
The AC1 control change number is specified by the Multi
Part or A/D Part parameter AC1 CONTROLLER
NUMBER, and the AC2 control change number is specified
by the Multi Part or A/D Part parameter AC2 CONTROLLER
NUMBER.
1.3 Channel mode messages
These messages specify the basic operation of a part.
1.3.1
All Sound Off
This message silences all currently-sounding notes on the
corresponding channel.
However, the settings of channel messages such as Hold 1
and Sostenuto will be maintained.
Control#
Parameter
Data Range
120
All Sound Off
0
1.3.2
Reset All Controllers
This message resets the following controllers to their default
values.
Controller
Value
Pitch bend change
±
0 (center)
Channel pressure
0 (off)
Polyphonic key pressure
0 (off)
Modulation
0 (off)
Expression
127 (maximum)
Hold
0 (off)
Portamento
0 (off)
Sostenuto
0 (off)
Soft pedal
0 (off)
Portamento control
Reset the portamento source
note number that was received
RPN
Number unset, internal data is
not affected.
NRPN
Number unset, internal data is
not affected.
The following data is not changed
Parameter values specified by program change, bank select
MSB/LSB, volume, pan, effect send levels 1, 3, 4, RPN and
NRPN.
Control#
Parameter
Data Range
121
Reset All Controllers
0
1.3.3
All Note Off
This message turns off all notes which are currently on for
the corresponding part.
However, if Hold 1 or Sostenuto are on, notes will continue
to sound until these are turned off.
Control#
Parameter
Data Range
123
All Note Off
0
1.3.4
Omni Off
Perform the same processing as when All Note Off is
received.
Control#
Parameter
Data Range
124
Omni Off
0
1.3.5
Omni On
Perform the same processing as when All Note Off is
received.
Control#
Parameter
Data Range
125
Omni On
0
1.3.6
Mono
Perform the same processing as when All Sound Off is
received, and if the value (mono number) is in the range of
0...16, set the corresponding channel to Mode4* (m = 1).
Control#
Parameter
Data Range
126
Mono
0...16
* Mode4 is a state in which only channel messages on the
specified channel will be received, and notes will be
sounded individually (monophonically).
MIDI data format
Summary of Contents for MU128
