background image

 

  

 

 
 

 

S32G2 Vehicle Network Processor - Clock 
Configuration Guide 

by: NXP Semiconductors 

1. Introduction 

NXP’s S32G2 is a family of high-performance 
vehicle network processors that combines Controller 
Area Network (CAN), Local Interconnect Network 
(LIN), and FlexRay networking with high-data-rate 
Ethernet networking. It also combines a functional 
safe-core infrastructure with MPU cores and includes 
high-level security features. 

S32G2 supports multiple clock sources for clock 
generation: 

 

Fast Internal RC Oscillator (FIRC) (48 MHz) 

 

Slow Internal RC Oscillator (SIRC) (32 KHz) 

 

Fast External Crystal Oscillator (FXOSC) (20 
– 40 MHz) 

 

Phase-Locked Loops (PLLs) 

 

Digital Frequency Synthesizer (DFS) modules 

This application note is intended to provide the user 
values for commonly used PLL/DFS configurations. 

This document is accompanied with an attached clock 
configurator - S32G2_Clock_Configurator.xlsx. The 
calculator simplifies the clock configuration process 
by helping user find the recommended and validated 
values of PLL parameters (MFI, MFN and DIV), DFS 
parameters (MFI and MFN), MC_CGM parameters 

NXP Semiconductors 

Document Number: AN13354 

Application Notes 

Rev. 1 , 11/2021 

Contents 

1.

 

Introduction .................................................................... 1

 

2.

 

PLL ................................................................................ 2

 

3.

 

DFS ................................................................................ 4

 

4.

 

Clock calculator design ................................................... 6

 

4.1

 

Options tab ........................................................... 6

 

4.2

 

Configuration tab.................................................. 7

 

4.3

 

Spread spectrum tab.............................................. 8

 

4.4   

Clock calculator key considerations....................... 9

 

5.

 

Spread Spectrum ........................................................... 10

 

5.1

 

Frequency modulation programming ................... 10

 

5.2

 

Spread Spectrum Considerations ......................... 11

 

5.3

 

Example code ..................................................... 12

 

6

 

Clock Configuration using S32DS Clocks Tool .............. 13

 

7

 

References .................................................................... 15

 

Summary of Contents for S32G2

















Reviews: