-3 DC3 DD Command (Reading Density Difference Setting Command)
[Explanation]
This command is for setting the density difference allowable from the darkest mark in the CA and EA
modes.
After setting the difference, marks thinner than the setting are cancelled and those in the allowable
range are all output.
The density difference is set at "01" by default. In this case, mark data of the darkest density are
output.
This setting is not stored after the power is turned off.
* This applies to when the CAN command is executed.
[Format]
DC3
D
D
N1 N2
CR
(13H) (44H) (44H)
(0DH)
N1N2: 2-byte ASCII code
9.Control Commands
-4 DLE T Command (Timing Format Setting Command)
[Explanation]
This command is for setting mark read timing (timing mark type). If the DIP switch setting has not
been changed, the setting by this command is not required when the power is turned on.
When the T command is executed, the set value remains unchanged unless the device is reset or the
power is turned off.
When using the timing control type, be sure to set the read timing by this command.
-4-1 In SR-450 (SR-410/430 compatible) mode
[Format]
e
ci
v
e
d
s
i
h
T
r
et
u
p
m
o
C
t
s
o
H
e
v
ie
c
e
R
R
C
N
X
T
S
R
C
T
E
L
D
(10H) (55H)
(0DH)
(02H)
(0DH)
* N: Specifies the format (1-byte ASCII numerical code between 1 and 5)
N values determine the mark read areas in the formats shown in the table below:
Setting method of timing control type
Specifying the timing control type with N = 1 when specifying the T command sets the read area at
three times of the timing mark.
[Format]
DLE
T
CR
STX
1
CR
(10H) (55H) (0DH) (02H) (31H)
(0DH)
t
N
a
m
r
o
f
g
n
i
m
it
d
a
e
r
k
r
a
M
e
1
p
y
t
l
o
rt
n
o
c
g
n
i
m
i
T
2
e
p
y
t
r
e
d
n
u
-t
c
e
ri
D
3
d
e
s
u
t
o
N
4
e
p
y
t
k
r
a
m
-
o
t-
k
r
a
M
)
d
a
e
r
e
b
o
t
t
o
n
e
c
a
p
s
k
n
al
b
r
o
d
n
e
(
5
e
p
y
t
k
r
a
m
-
o
t-
k
r
a
M
)
d
a
e
r
e
b
o
t
e
c
a
p
s
k
n
al
b
r
o
d
n
e
(
9.Control Commands
- 27 -
Summary of Contents for SR-450
