On the next section, the operations to be performed to modify the parameters are described.
4.A - Modification of Function 01 - WIND THRESHOLD
4.G - Modification of Function 16 - ANEMOMETRIC TEST
4.I - Modification of Function 18 - BUTTONS LOGIC
4.B - Modification of Function 02 - SUN THRESHOLD
4.E - Modification of Function 11 - FABRIC RELEASE
4.H - Modification of Function 17 - RADIO TEST
4.L - Function 29 - RECEIVER RESET
01 - wind theshold
02 - sun threshold
07 - working time
08 - «air change» function
11 - fabric release
12 - orientation time
16 - anemometric test
17 - radio test
18 - buttons logic
29 - receiver reset
RECEIVER CODE FUNCTIONS
It’s NOT possible for sensor 593.K.XB.00 (in this case you can modify
only by buttons on sensor).
With 593.K.XS.00 is necessary a «10 channels» transmitter.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. If you have 593KXS00 you must store the sun-wind sensor in a free
channel of transmitter (read manual of sun-wind sensor at the
section 6) and select this channel.
03. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 time
NEXT
. 01 appears on the display.
04. Press 1 time
STOP
.The receiver signal the new value.
Examples:
if threshold = 08 Km/h:
p
8 (8 short movements)
if threshold = 15 Km/h:
p
1 - pause -
p
5
if threshold = 30 Km/h:
p
3 - pause -
p
1 long
05. Using
PREV
and
NEXT
to set the new value. (from 5 Km/h at 35
Km/h. From factory set to 15 Km/h).
Examples:
for threshold 08 Km/h: (0 time PREV) - 8 times NEXT
for threshold 15 Km/h: 1 time PREV - 5 times NEXT
for threshold 30 Km/h: 3 times PREV - (0 time NEXT)
07. Press 1 time
STOP
.The receiver signal the new value.
It’s NOT possible for sensor 593.K.XB.00 (in this case you can modify
only by buttons on sensor).
With 593.K.XS.00 is necessary a «10 channels» transmitter.
You must before active the «sun function» on transmitter on motor
channel (read the section number 1 of this manual).
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. If you have 593KXS00 you must store the sun-wind sensor in a free
channel of transmitter (read manual of sun-wind sensor at the
section 6) and select this channel.
03. Press
MENU
for about 5 seconds.
rS
appears on the display.
04. Press 2 times
NEXT
. 02 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value
Examples:
if threshold = 07 Klux:
p
7 (7 short movements)
if threshold = 18 Klux:
p
1 - pause -
p
8
if threshold = 20 Klux:
p
2 - pause -
p
1 long
06. Using
PREV
and
NEXT
to set the new value (from 1 Klux at 45
Klux. From factory set to 16 Klux).
Examples:
for threshold 07 Klux: (0 time PREV) - 7 times NEXT
for threshold 18 Klux: 1 time PREV - 8 times NEXT
for threshold 20 Klux: 2 times PREV - (0 time NEXT)
07. Press 1 time
STOP
.The receiver signal the new value.
4.F - Modification of Function 12 - ORIENTATION TIME
All rights reserved.
STAFER S.p.a. - via Malpighi, 9 - 48018 Faenza (RA) ITALY
Tel. (+39) 0546.624811 - Fax. (+39) 0546.623141 - www.stafer.com
It is possible to exit the «receiver menu» at
any time by pressing the button
MENU
briefly.
3. DELAY ASSOCIATED TO THE SEQUENCER CHANNEL (only 594.T.X.00)
The «10 channels transmitter» have a virtual channel called sequencer «
SE
», which send the selected command in succession for all the active radio channels.
To select the
Sequencer
, scroll the list of channels until
SE
symbol appears. It is possible to set the interval (from 1 to 10 sec) of time which must pass between the
transmission on one channel and the next. The factory sets the delay at 1 second. The use of high intervals of time can negatively effect on the battery life.
To modify the setting:
MENU
Press STOP and then MENU and
hold the buttons for about 3
seconds, until the symbol
ch
is
displayed.
Press NEXT. The
Sd
symbol
appears on the display.
B
Press STOP to save the setting.
E
To exit, press twice MENU or
wait about 15 seconds (the
display switches off).
F
MENU
Press STOP. The currently set
value appears on the display (from
01 to 10 sec).
C
Use PREV and NEXT to set the
required value.
D
A
2x
4. RECEIVER MENU
After storing a radio channel of the transmitter on a receiver, it is possible to modify some operating parameters of the receiver directly from the transmitter. To
identify the editable settings, refer to the instruction manual of the receiving device.
To modify an operating parameter:
Select the channel associated to the
receiver.
B
MENU
Press MENU on the transmitter for
about 5 seconds, until
rS
symbol
appears.
C
Use PREV and NEXT to select the
code of the parameter to edit (see
table).
D
Press STOP. The receiver will show
the current value of the parameter.
E
Use PREV and NEXT to set the
new parameter value.
F
Press STOP. The receiving device
shows the new value of the
parameter.
A
CONVENTIONS USED IN THE EXAMPLES:
Ÿ
On the following example with
p
is indicated a short upward movement (example:
p
3 = 3 short upward movements of the motor).
Ÿ
On the following example with
q
is indicated a short downward movement (example:
q
1 = 1 short downward movement of the motor).
Ÿ
Some receiver may display the settings in another way (i.e. not with motor movements, but with visual and acoustic signals) or not display the settings. In
these cases, refer to the instruction manual of the receiver.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 time
PREV
and 1 time
NEXT
. 11 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value.
Example: if parameter value = 2:
p
2 (2 short upward movements)
05. Using
PREV
and
NEXT
to set the new value (from 1 at 5. 1 is
function OFF. From factory is set 1)
Example: for parameter = 2; (0 time PREV) - 2 times NEXT
06. Press 1 time
STOP
.The receiver signal the new value.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 time
PREV
and 2 times
NEXT
. 12 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value.
Example: if parameter value = 4:
p
4 (4 short upward movements)
05. Using
PREV
and
NEXT
to set the new value (from 1 to 5. 1 is
function OFF. From factory is set 1).
Example: for parameter = 4; (0 time PREV) - 4 times NEXT
06. Press 1 time
STOP
. The receiver signal the new value.
Only available with 593.K.RS.00 and 593.K.RA.00.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 TIME
PREV
and 6 times
NEXT
. 16 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value.
Function active:
p
1
(1 short upward movement)
Function not active:
q
1
(1 short descent movement)
05. Press
PREV
to disable the function (
Of
appears on the display)
or
NEXT
to enable the function (
On
appears on the display). Factory
set is Of.
06. Press 1 time
STOP
. The receiver signal the new value.
Function active:
p
1 - Function not active:
q
1
Only available with 593.K.XS.00 and 593.K.XB.00.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 TIME
PREV
and 7 times
NEXT
. 17 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value.
Function active:
p
1
(1 short upward movement)
Function not active:
q
1
(1 short descent movement)
05. Press
PREV
to disable the function (
Of
appears on the display)
or
NEXT
to enable the function (
On
appears on the display). Factory
set is On.
06. Press 1 time
STOP
. The receiver signal the new value.
Function active:
p
1 - Function not active:
q
1
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 1 time
PREV
and 8 times
NEXT
. 18 appears on the display
04. Press 1 time
STOP
. The receiver signals the current value.
Hold to run:
p
1
(1 short upward movement)
Pulse:
q
1
(1 short descent movement)
05. Press
PREV
for logic «pulse» (
Of
appears on the display) or
NEXT
for logic «hold to run» (
On
appears on the display). Factory
set is Of.
06. Press 1 time
STOP
. The receiver signal the new value.
Hold to run:
p
1 - Pulse:
q
1
WARNING:
For this procedure, use ONLY A CHANNEL STORED ON THE RECEIVER THAT YOU WANT TO RESET if more devices are tuned on the same
channel, power on only the device to be resetted.
01. Select the channel tuned on the receiver to be «resetted».
02. Press
MENU
for around 5 seconds.
rS
appears on the display.
03. Press 2 times
PREV
and 9 times
NEXT
. 29 appears on the display.
04. Press 1 time
STOP
. The receiver signals that it is ready for the memory reset (with visual or acoustic signals, see the receiver instruction manual); on
the transmitter, all the leds and display segments come on intermittently for a few seconds.
Then they light on.
05.
until the receiver signals that the factory settings have been restored.
Press together
PREV
and
NEXT
06. Follow the instruction manual of the receiver to re-install the receiver.
All products and technical specifications given in this document are subject to variation without notice. Unless previously and specifically authorised by STAFER, the device must be
used exclusively with transmitters produced by STAFER.
STAFER cannot be consider responsible for damage caused by improper, incorrect or unreasonable uses.
Since the factory is set at 1 (NOT active). Possible values from 1 to 6.
01. Select the correct radio channel and bring the motor on the
intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 8 times
NEXT
. 08 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value
Example:
if time = 2 sec:
p
2 (2 short upward movements)
if time = 5 sec:
p
5 (5 short upward movements)
05. Using
PREV
and
NEXT
to set the new value:
for time 3 sec: 0 times
PREV
and 3 times
NEXT
for time 6 sec: 1 time
PREV
and 6 times
NEXT
06. Press 1 time
STOP
. The receiver signal the new value.
To call the function, press the button «THIRD SWITCH»..
4.C - Modification of Function 07 - WORKING TIME (only for 594.R.EN.00)
4.D - Modification of Function 08 - AIR CHANGE (only for 594REN00)
01. Select the correct radio channel and bring the motor on the intermediate position.
02. Press
MENU
for about 5 seconds.
rS
appears on the display.
03. Press 7 times
NEXT
. 07 appears on the display.
04. Press 1 time
STOP
. The receiver signals the current value.
Example:
if it gets up for sec. = 2:
p
2 ( 2 short upward movements)
if it gets up for sec. = 35:
p
3 - pause -
p
5
if it gets up for sec. = 120:
p
1 pause
p
2 pause
p
1long
05. Using
PREV
and
NEXT
to set the new value:
for time = 3: 0 time
PREV
and 3 times
NEXT
(the value must be between 5 and 240. Factory set is 120sec.)
06. Press 1 time
STOP
. The receiver signal the new value.
