White Mini-Seis III Pro Operating Manual Download | Manualshive

Page: 39 / 49

background image

Mini-Seis III Pro™ Operating Manual

Page 39

CLI Commands

There are numerous commands that can be used to setup and control Pro operation. It is
best to use these commands with the Command Prompt in Seismograph Data Analysis. All
commands persist through a power cycle.

Command Description

Parameters

AU enable

Get or set whether the air channels are used. If enabled is 1, air
channels are included. If enabled is 0, air channels are
excluded. If passed with no parameter, returns the current
value.

enable:
0 = Air is disabled
1 = Air is enabled

AW used

Get or set whether A-weighting is used. If the A-weighting
board is not installed, the result will always be 0. If passed with
no parameter, returns the current value. If the A weight board is
installed and enabled the return value will be 2.

used:
0 = Not used
1 = Use A-weighting

BV

Get the last raw battery voltage in the format #.##.

None

CHEN

channels

Enables 8 channels (channels = 2), four channels (channels = 1),
or none (channels = 0) and configures enabled channels as
follows:
Channels 1-3: Seismic
Channel 4: Air
Channels 5-7: Seismic
Channel 8: Air
The commands SSP 0, SSP 1, or SSP 2 should be used to
configure the range, units, and min.

channels:
0 = All disabled
1 = Channels 1-4 enabled,
channels 5-8 disabled
2 = All enabled

CHG

Returns the external charging voltage.

None

CL

Clears the system log.

None.

CO text

Get or set the text of the comment preset.  Text is all characters
following the space following CO (up to 126 characters, so
comments may include spaces and punctuation in addition to
numbers and letters.  The line feed character (‘\n’ / 0x0A) is
treated as a carriage return.  If passed with no parameters,
returns the current text for the comment.

text:
Any combination of up to
126 ASCII characters from
0x20 (space) to 0x7E
(tilde), inclusive, as well
as 0x0A (line feed).

COMP

enabled

Turn compression on/off when downloading.

Enabled:

0 = Disable compression
1 = Enable compression

CS enable

Enable or disable comment inclusion with subsequent records.
Note that comment text is set using the CO command. If sent
with no parameters, returns the current enable value.

enable:
0: Do not include the
comment preset on
subsequent records.
1: Include the comment
preset with records
collected following
enabling comments.

DU seconds

Get or set the waveform duration in seconds.

seconds:
1 to 120

EM

Erase memory

none

ER mode
[HHMM]

Set automatic reporting mode and parameters. Note that HH and
MM must be 0-padded.
If passed with no parameters and the current mode is 0 or 1,
returns only the value of the current mode.
If passed with no parameters and the current mode is 2 or 3,
returns the current values of all parameters.

mode:
0 = Disable automatic
reporting
1 = Triggered mode
2 = Fixed mode
3 = Interval mode

HH: 00–23 (required for
fixed and interval modes)

«
...
37
38
39
40
41
...
»

Summary of Contents for Mini-Seis III Pro


















































Reviews:

No comments

Related manuals for Mini-Seis III Pro

Brand: Kane Pages: 4

Brand: LaserLine Pages: 24

Brand: Pangea Pages: 2

Brand: Schneeberger Pages: 35

Brand: Percussion Play Pages: 3

Brand: Omega Pages: 13

BUCKMASTERS 1500

Brand: Sig Sauer Pages: 2

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: Fly Henry Pages: 5

Brand: Hanna Instruments Pages: 28

Brand: Omega Pages: 4

Brand: NetThings Pages: 3

Celviano AP-60R

Brand: Casio Pages: 44

Brand: iBike Pages: 52

EZP3 EASY Piano

Brand: Lowrey Pages: 59

Brand: Chauvin Arnoux Pages: 12

Brand: Fluke Pages: 97

Brand: Hall Research Technologies Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands