Datalogic IO-Link S100 Series, Instruction Manual

Teach-in Parameters
Index

(dec)

Parameter 

Object Name

Lenght

Subindex

(offset)

Value/Range

Description

Data Type Access* Remark

0x003A (58)

 TI Select

1 octet

0x00 = SSC1 (default, C/Q pin and DO 

pin)

Selection for Teach-in channel (volatile)

UIntegerT

R/W

C/Q and DO outputs are antivalent. 

Teach SSC1 equals to teach SSC2

0x003B (59)

TI Result

1 octet

1(0) 

2(4)

3(5)

Teach-in State
Flag SP1 TP1
Flag SP2 TP1

See IO-Link Smart Sensor Profile

UIntegerT4 

BooleanT 

BooleanT

RO

0x003C (60)

SSC1 Param

2 octets

2 octets

1(16)

2(0)

280-1950

Not used

Switching threshold

UIntegerT

R/W

Saved in non-volatile memory

0x003D (61)

SSC1 Config

1 octet

1 octet

1(24)

2(16)

0x00: High Active

0x01: Low Active (default)

0x01: Single Point (default)

C/Q pin configuration

UIntegerT 

UIntegerT 

R/W

Saved in non-volatile memory

2 octets

3(0)

0 ..2 Hysteresis

UIntegerT

0x003E (62)

SSC2 Param

2 octets

2 octets

1(16)

2(0)

280-1950

Non used

Switching threshold

UIntegerT

R/W

Saved in non-volatile memory

0x003F (63)

SSC2 Config

1 octet

1 octet

1(24)

2(16)

0x00: High Active (default)

0x01: Low Active

0x01: Single Point (default)

DO pin configuration

UIntegerT 

UIntegerT 

R/W

Saved in non-volatile memory            

2 octets

3(0)

0 ..2 Hysteresis

UIntegerT

0x0040 (64)

Sensitivity 

selection

1 octet

0 ..10 Sensitivity

Sensitivity

UIntegerT

R/W

Saved in non-volatile memory

Device Specific Parameters

Index

(dec)

Parameter 

Object Name

Lenght

Subindex

(offset)

Value/Range

Description

Data Type

Access* Remark

0x0048 (72)

Delay Settings

1 octet

1(8)

0 = no delay (default)

0x4 = Delay OFF

Select Delay mode (OFF)

UIntegerT

R/W

Saved in non-volatile memory.

Max. Value 255 ms

*Available for future Beta samples

1 octet

2(0)

0...(2^8)-1

Delay value =  Delay [ms] 

UIntegerT

R/W

0x00B4 (180)

Output type

1 octet 

1 octet

1(8) 

2(0)

0x01 = PNP (default)
0x03 = Push Pull 

(1)

0x01 = PNP (default)
0x03 = Push Pull
0x04 = Input

Output type of C/Q pin when in SIO mode

Output type of DO pin

UIntegerT 

UIntegerT

R/W 

R/W

Saved in non-volatile memory

(1)

 The No Output configured in Push Pull mode with an NPN load does not reactivate after a short circuit condition. Remove the short circuit condition and cycle power to the sensor.

*RO = read only, WO = write only, R/W = read/write