Silicon Laboratories WF200 Quick Start Manual Download

Page: 5 / 14

1.4.2 Access Point Demo

This demo configures the Raspberry Pi and WF200 to work as a Wi-Fi access point which can accept stations. To start it, run:

sudo wfx_demo_ap

Then it is possible to connect to the Raspberry Pi using a Wi-Fi capable device and the following credentials:

• SSID:

silabs-pi-demo

• Passphrase:

default_password

On the device, use a browser to open

http://silabs-pi-demo.wlan/

1.5 Update SD Card

To download and install an SD card image, go to

https://github.com/SiliconLabs/wfx-linux-tools/blob/master/RELEASES.md

1.6 Software Repositories

For development purposes, software can be found in the locations listed below:

• WF200 firmware is available in

https://github.com/SiliconLabs/wfx-firmware

• The Linux driver is available in

https://github.com/SiliconLabs/wfx-linux-driver

1.7 Documentation

Complete documentation for development with a Raspberry Pi is available here:

https://github.com/SiliconLabs/wfx-linux-tools/blob/

master/README.md

QSG166: WF200 Wi-Fi Development Kit Quick Start Guide

Getting Started with Raspberry Pi and Linux

silabs.com

| Building a more connected world.

Rev. 0.4 | 5

Summary of Contents for WF200















Search results

Summary of Contents for WF200

Reviews:

Related manuals for WF200

Brands by name

Popular brands

Silicon Laboratories WF200, Quick Start Manual

Search results

Summary of Contents for WF200

Reviews:

Related manuals for WF200

Brands by name

Popular brands