background image

2009 NETCONS, s.r.o. 

 

 

 

Page 11 of 16 

ERRORREPLY=NO 

Deactivates sending of information 
SMS for each received SMS command, 

which was not executed due to any 
error. 

ERRORREPLY =NO – OK 

Conf 

ERRORREPLY? 

Information message: Request for 
ERRORREPLY settings 

ERRORREPLY =(NO),YES 

Conf 

OUTPUT=REMEMBER 

Output power socket remember it’s 

status after it’s unplugged or central 
power is interrupted 

OUTPUT=REMEMBER – 

OK 

Conf 

OUTPUT=ON 

Output power and microrelay will be 

turned on after it’s unplugged or 
central power is interrupted 

OUTPUT=ON – OK 

Conf 

OUTPUT=OFF 

Output power and microrelay will be 

turned off after it’s unplugged or 
central power is interrupted 

OUTPUT=OFF – OK 

Conf 

OUTPUT? 

 

Information message: Request for 
initial mode configuration of 
output power socket and 
microrelay 

 

OUTPUT=(REM), ON, OFF  Conf 

INPUT=ALARMHIGH 

Detection mode for external detector. 

In this case alarm is generated after 
high voltage is detected. 

INPUT=ALARMHIGH– OK 

Conf 

INPUT=ALARMLOW 

Detection mode for external detector. 

In this case alarm is generated after 
low voltage is detected. 

INPUT=ALARMLOW – OK 

Conf 

INPUT? 

Information message: Request for 
input mode configuration

 

INPUT=DISCONNECTED, 

(CONNECTED) 

Conf 

VERSION 

Request for firmware version 

Ver. 1.0.6 (c) 2008 

Ctrl 

RINGON 

Back call is realized to the number 
of the incoming SMS. Usefull 
feature when using prepaid cards 
to keep card active. 

/no confirmation 

Ctrl 

 

 

If bad command is received, power socket replies with „message – ERROR!“ 

message  

 

Capitals and small alphabets are not recognized in commands 

 

SMS messages longer than 20 characters are automatically ignored 

9. Alarms and microrelay 

9.1 External detector alarms 

External detectors can be used for various alarm detections, for example 
motion, fire, gas, water, opened door/window detection and so on. Detectors 

are connected over 3.5 mm jack. It is possible to use more different detectors 
divide by jack divider, total current shouldn’t be more than 50mA. Only first 
alarm within 60 seconds is indicated. 

 

Command 

Description 

Response 

Type 

ALARMON 

Activated is alarm detection by 
external detectors. 

AlarmOn = OK 
Alarm – NO sensor 

Ctrl

 

ALARMOFF 

Deactivated is alarm detection by 
external detectors. 

AlarmOff = OK 

Ctrl

 

Summary of Contents for IQSW-GSM

















Reviews: