background image

 

Parameter lock. 

This security feature locks out selected levels or single 

parameters prohibiting tampering and inadvertent programming changes. 

0000 

All parameters are locked. 

0001 

Only SP is adjustable. 

0010 

USER (level) and A1(parameter) are adjustable. 

0011 

USER

PID(level) and A1

A2(parameter) are adjustable. 

0100 

USER

PID

OPTI(level) and A1

A2(parameter) are adjustable. 

1000 

Additional A3(parameter). All parameter you can find out,but 
can’t adjustable.   

1001 

Additional A3(parameter)

only SP is adjustable. 

1010 

Additional A3(parameter). USER(level) and A1(parameter) are 
adjustable. 

1011 

USER

PID (level) and A1

A2

A3 (parameter) are adjustable. 

1100 

All parameters in all level are opened. 

 

 

 

THIRD PROGRAMMING LEVEL PARAMETERS 

CODE 

DESCRIPTION RANGE 

Default 

 

Input type selection. 

TYPE 

RANGE(

) RANGE(

-50 

 1000 

-58 

 1832  

-50 

 1370 

-58 

 2498 

-270 

 400 

-454 

 752 

-50 

 1000 

-58 

 1832 

 1800 

32 

 3272 

-50 

 1750 

-58 

 3182 

-50 

 1750 

-58 

 3182 

-50 

 1300 

-58 

 2372 

-50 

 1800 

-58 

 3272 

D-PT 

-200 

 850 

-328 

 1652 

J-PT 

-200 

 600 

-328 

 1112 

LINE 

-1999 

 9999 

 

  Refer to figure. 

 

Unit of process value.

 The parameter is not displayed when 

=LinE

   

Degrees C. 

Degrees F. 

 

 

Used to limit the process value when linear input 
(type=line) signal is out of range. 
None= 

this function is not used.

 

Lo = 

The process value will be limited to LoLt when input 

signal is lower than the scale range. 

Hi = 

The process value will be limited to HiLt when input 

signal is higher than the scale range. 

Lo.Hi = 

The process value will be limit within the range of 

LoLt to HiLt when input signal is out of scale.

 

nonE

Lo 

Hi

Hi.Lo 

 

 

Decimal Point selection. 

0000

No decimal point. 

000.0

0.1 resolution 

00.00

0.01 resolution, used for linear input only. 

0.000

0.001 resolution, used for linear input only. 

After changing the decimal point parameter please re-check 
all the parameters.

 

0000 

000.0 
00.00 
0.000 

0000 

  Output control action. 

 :Reverse 

action 

for heating. 

:Direct action for 

cooling. 

 

 

8

Summary of Contents for VD 26 Series












Reviews: