manualshive.com logo in svg

3Com Router 3000 DSL Series, Command Reference Manual

The 3Com Router 3000 DSL Series offers reliable and high-performing connectivity. Our Command Reference Manual provides comprehensive guidance for optimal usage. Available for free download from our website, this manual equips users with detailed instructions and troubleshooting tips, ensuring seamless and hassle-free utilization of this exceptional product.

Share
Download
background image

Integrated IS-IS Configuration Commands

617

this time 3 times of hello interval. That is to say, if the router does not receive hello 
message from its neighbor 3 times, it would determine that the neighbor is dead. 
User can adjust this parameter according to the network.

For the related command, see isis timer hello.

Example

 Set the dead interval of Level-2 to 60 seconds on Interface serial1/0/0.

[3Com] interface serial1/0/0

[3Com-Serial1/0/0] isis timer dead 20 level-2

isis timer hello

Syntax

isis timer hello seconds [ level-1 | level-2 ]

undo isis timer hello [ level-1 | level-2 ]

View

Interface view

Parameter

■

seconds: Specifies the Hello message interval, ranging from 3 to 255 and 
measured in seconds. The default value is 10 seconds.

■

level-1: Specifies the Level-1 Hello interval.

■

level-2: Specifies the Level-2 Hello interval.

■

If neither Level-1 nor Level-2 is specified, it is defaulted to Level-1-2 Hello 
message interval, that is, both Level-1 and Level-2 take effect.

Description

Using the isis timer hello command, you can configure the interval of sending 
hello message of corresponding level. Using the undo isis timer hello command, 
you can restore the default value, that is, 10 seconds.

On a broadcast link, Level-1 and Level-2 hello messages will be sent respectively 
and their intervals should also be set respectively. Such settings are unnecessary on 
point-to-point links. The shorter the sending interval is, the more system resources 
are occupied to send hello messages. Therefore, the interval should be set 
according to actual conditions.

For the related command, see isis timer dead.

Example

 Set the Hello message of Level-1 to be transmitted every 20 seconds on Interface 
serial1/0/0.

[3Com] interface serial1/0/0

[3Com-Serial1/0/0] isis timer hello 20 level-1

isis timer lsp

Syntax

isis timer lsp 

time

undo isis timer lsp

Summary of Contents for Router 3000 DSL Series







































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Router 3000 DSL Series

iDirect iQ Desktop+ Installation, Support, And Maintenance Manual preview
iQ Desktop+
Brand: iDirect Pages: 52
LogLogic LX 1010 Quick Start Manual preview
LX 1010
Brand: LogLogic Pages: 30
Mercusys MR30G Quick Installation Manual preview
MR30G
Brand: Mercusys Pages: 35
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
pivotal COMMWARE ECHO 5G How To Set Up preview
COMMWARE ECHO 5G
Brand: pivotal Pages: 2
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Brand: TP-Link Pages: 87
Avaya ERS 5510 Technical Configuration Manual preview
ERS 5510
Brand: Avaya Pages: 73
X-Micro IEEE 802.11b User Manual preview
IEEE 802.11b
Brand: X-Micro Pages: 49
Airlink101 AR325W Quick Installation Manual preview
AR325W
Brand: Airlink101 Pages: 13
Rajant Corporation BreadCrumb CX1 User Manual preview
BreadCrumb CX1
Brand: Rajant Corporation Pages: 40
MSNswitch UIS-322b Quick Installation Manual preview
UIS-322b
Brand: MSNswitch Pages: 2
UNICORECOMM UM620N User Manual preview
UM620N
Brand: UNICORECOMM Pages: 19
Doro GW7001 Quick Installation Manual preview
GW7001
Brand: Doro Pages: 50
Extron electronics Network Adapter AC AAP Specifications preview
Network Adapter AC AAP
Brand: Extron electronics Pages: 2
Trend Micro R610 Series Quick Start Manual preview
R610 Series
Brand: Trend Micro Pages: 2
Gemtek WL-613F User Manual preview
WL-613F
Brand: Gemtek Pages: 29
Avaya VSP 8284XSQ-AC Quick Install Manual preview
VSP 8284XSQ-AC
Brand: Avaya Pages: 2
Delta Electronics DVP Series PLC DVP04TC-H2 Instruction Manual preview
DVP Series PLC DVP04TC-H2
Brand: Delta Electronics Pages: 2

Brands by name

Popular brands

Load more brands