70
CONTROL ASSIGN Parameters > ASSIGN SETTING
ASSIGN SETTING
ASSIGN 1–ASSIGN 16
For each parameter, you can specify, in detail, which controller will
control which parameter. You can create 16 sets of such assignments.
Parameter
Value
Explanation
SW
OFF, ON
Turns the ASSIGN 1–16 on/off.
TARGET
This selects the parameter to be changed.
Refer to “TARGET list” (p. 71).
MIN
*6
This sets the minimum value for the range in
which the parameter can change.
The value differs depending on the parameter
assigned for TARGET parameter.
MAX
*6
This sets the maximum value for the range in
which the parameter can change. The value
differs depending on the parameter assigned
for TARGET parameter.
SOURCE
*6
This selects the controller that will operate the
parameter.
Refer to “SOURCE list” (p. 76).
MODE
*6
MOMENT
The normal state is Off
(minimum value), with the
switch On (maximum value)
only while the footswitch is
depressed.
TOGGLE
The setting alternately switches
to OFF (minimum value) and
ON (maximum value) each time
the footswitch is pressed.
ACT LOW
0–126
You can set the controllable
range for target parameters
within the source’s operational
range.
Target parameters are
controlled within the range set
with ACT LOW and ACT HIGH.
You should normally set ACT
LOW to 0 and ACT HIGH to 127.
ACT HIGH
1–127
RISE TIME
*5
*6
*7
0–100
Adjusts the
time over
which the
target changes
from minimum
to maximum.
Set this
to zero if
you want
the value
to change
immediately,
such as for
a parameter
that turns
a value on/
off or for tap
input.
FALL TIME
*5
*6
*7
0–100
Adjusts the
time over
which the
target changes
from maximum
to minimum.
INPUT SENS
0–100
Adjusts the input sensitivity
when STRING1–STRING6, STR
HiC–STR LowB, STRING ALL, or
NORMAL INPUT is selected as
the SOURCE.
WAVE PEDAL
FORM
*1
SAW
TRI
SINE
Parameter
Value
Explanation
WAVE PEDAL
RATE
*4
0–100, BPM
Œ
–
`
Specifies the time for one cycle
of the wave pedal.
MIDI CH
*2
*3
SYSTEM
The message is transmitted on
the MIDI channel specified by
1–16
The message is transmitted on
the specified MIDI channel.
MIDI CC#
*2
0–127
The message is transmitted
using the specified controller
number.
MIDI CC# MIN *2
0–127
Selects the minimum value of
the transmitted CC# message.
MIDI CC#
MAX
*2
0–127
Selects the maximum value of
the transmitted CC# message.
MIDI PC#
*3
1–128
Specifies the program number
that is transmitted.
MIDI PC#
BANK MSB
*3
OFF, 1–127
Specifies the bank select MSB
that is transmitted. If this is
OFF, the bank select MSB is not
transmitted.
MIDI PC#
BANK LSB
*3
OFF, 1–127
Specifies the bank select LSB
that is transmitted. If this is
OFF, the bank select LSB is not
transmitted.
*1 Valid when the SOURCE is set to WAVE PEDAL.
*2 Valid when the TARGET is set to MIDI CC#.
*3 Valid when the TARGET is set to MIDI PC#.
*4 Refer to “About effects when a note value is selected as a setting”
*5 Valid when the SOURCE is set to other than EXP1, EXP2, GK VOL,
or WAVE PEDAL.
*6 Valid when the TARGET is set to other than BPM TAP, DLY1 TAP,
DLY2 TAP, MST DLY TAP, FX1 DLY TAP, FX2 DLY TAP, FX3 DLY TAP, PU
SELECT UP, PU SELECT DOWN, SEQ RETRIGGER, SYNC RETRIGGER,
or MIDI PC#.
*7 Valid when the SOURCE is set to other than STRING1–STRING6,
STR HiC–STR LowB, STRING ALL, NORMAL IN, or MIDI CC#.
