44
MIS-4220 / MIS-4220R / MIS-4230
45
Infinitely Expandable
Auto Power Command
Auto Power On
ASCII
R(0x52)
M(0x4D)
HEX
0x35
0x32
0x34
0x3D
Auto Power Off
ASCII
R(0x52)
m(0x6D)
HEX
0x35
0x32
0x36
0x3D
Auto Power On: Enables Power On by connecting AC Power
-
Supply even without Power On command.
Auto Power Off: Enables Power On by connecting AC Power
-
Supply and sending Power On command.
Input Source Command
Input Source
Change DVI
ASCII
R(0x52)
i(0x69)
HEX
0x35
0x32
0x36
0x39
Input Source
Change PC
ASCII
R(0x52)
p(0x70)
HEX
0x35
0x32
0x37
0x30
Input Source
Change HD
ASCII
R(0x52)
t(0x74)
HEX
0x35
0x32
0x37
0x34
Input Source
Change SD/DVD
ASCII
R(0x52)
d(0x64)
HEX
0x35
0x32
0x36
0x34
Input Source
Change S-VIDEO
ASCII
R(0x52)
s(0x73)
HEX
0x35
0x32
0x37
0x33
Input Source
Change VIDEO
ASCII
R(0x52)
v(0x76)
HEX
0x35
0x32
0x37
0x36
Command for selecting Input Mode
-
Tracking Command
Auto Tracking
ASCII
R(0x52)
a(0x61)
HEX
0x35
0x32
0x36
0x31
Manual Tracking
Frequency
ASCII
R(0x52)
F(0x46)
HEX
0x35
0x32
0x34
0x36
Manual Tracking
Phase
ASCII
R(0x52)
P(0x50)
HEX
0x35
0x32
0x35
0x30
Manual Tracking
Line Start
ASCII
R(0x52)
L(0x4C)
HEX
0x35
0x32
0x34
0x3C
Manual Tracking
Pixel Start
ASCII
R(0x52)
X(0x58)
0x35
0x32
0x35
0x38
Auto Tracking: Auto screen positioning command in Input Mode PC
-
Manual Tracking: Manual screen positioning command in Inpuit
-
Mode PC
Test Pattern Command
Test Pattern Red
ASCII
R(0x52)
5(0x35)
HEX
0x35
0x32
0x33
0x35
Test Pattern Green
ASCII
R(0x52)
6(0x36)
HEX
0x35
0x32
0x33
0x36
Test Pattern Blue
ASCII
R(0x52)
7(0x37)
HEX
0x35
0x32
0x33
0x37
Test Pattern White
ASCII
R(0x52)
8(0x38)
HEX
0x35
0x32
0x33
0x38
Return Screen
ASCII
R(0x52)
9(0x39)
0x35
0x32
0x33
0x39
Test Pattern Command
-
APL Command
APL On
ASCII
R(0x52)
x(0x78)
HEX
0x35
0x32
0x37
0x38
APL Off
ASCII
R(0x52)
y(0x79)
0x35
0x32
0x37
0x39
APL(Automatic Power Limit) On/Off
-
PDP Tx Command
PDP Tx Enable
ASCII
R(0x52)
H(0x48)
HEX
0x35
0x32
0x34
0x38
PDP Tx Disable
ASCII
R(0x52)
S(0x53)
HEX
0x35
0x32
0x35
0x33
Enable: RS232 IC Output(Tx) within PDP
-
Disable: RS232 IC Output(Tx) within PDP turns to High Impedance
-
state
Caution
- Do not enable Tx of plural PDP sets at the same time
when you control MPDP.
(Make sure only one set is enabled and the other sets
are disabled. If plural sets are enabled, it may cause
malfunction.)
Software Reset Command
Software
Reset
ASCII
R(0x52)
R(0x52)
HEX
0x35
0x32
0x35
0x32
Software Reset
-
Position Command
Position Up
ASCII
P(0x50)
u(0x75)
HEX
0x35
0x30
0x37
0x35
Position Down
ASCII
P(0x50)
d(0x64)
HEX
0x35
0x30
0x36
0x34
Position Left
ASCII
P(0x50)
l(0x6C)
HEX
0x35
0x30
0x36
0x3C
Position Right
ASCII
P(0x50)
r(0x72)
HEX
0x35
0x30
0x37
0x32
Position Reset
ASCII
P(0x50)
S(0x53)
0x35
0x30
0x35
0x33
Component, SVIDEO, Composite Video Input screen positioning
-
command
Global Offset Command
Global Offset On
ASCII
P(0x50)
L(0x4C)
HEX
0x35
0x30
0x34
0x3C
Global Offset Off
ASCII
P(0x50)
R(0x52)
HEX
0x35
0x30
0x35
0x32
Command to enlarge the display considering the seam between
-
two MPDP
Global Offset On: To enhance the continuity between MPDPs, data
-
for the Seam area is erased.
Video Zoom Control Command
Video Zoom Control
ASCII
P(0x50)
n(0x6E)
HEX
0x35
0x30
0x36
0x3E
- Video Zoom: Default Level is "5", controllable within "1"~"9"
-
Color Temp Command
Normal Mode
ASCII
G(0x47)
N(0x4E)
HEX
0x34
0x37
0x34
0x3E
Studio Mode
ASCII
G(0x47)
O(0x4F)
HEX
0x34
0x37
0x34
0x3F
Studio Mode: Sets to Colour Temperature approximately 3200K
-
Firmware Default Command
Firmware Default
Load
ASCII
F(0x46)
1(0x31)
HEX
0x34
0x36
0x33
0x31
Set values to default. Values before factory adjusting.
-
Factory Data Command
Factory Data Save
ASCII
F(0x46)
2(0x32)
HEX
0x34
0x36
0x33
0x32
Factory Data Load
ASCII
F(0x46)
3(0x33)
HEX
0x34
0x36
0x33
0x33
Factory Data Save: Data Save after adjusting
-
Factory Data Load: Load values of Factory Data
-
User File Load Command
User File Load
ASCII
F(0x46)
6(0x36)
HEX
0x34
0x36
0x33
0x36
Read and Load Picture Control Data from saved file
-
Reference - Application: Saved Picture Control Data is saved as a
-
file as the figure adjusted by the user
* File Format: ***.dat
* Data Structure (31 byte ASCII Code)
User Mode
Brightness, Contrast, Sharpness, Color, Tint
White Balance
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Device PC
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Device DTV
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Device DVD
Brightness, Contrast, Cr, Cb
Device VIDEO
Brightness, Contrast, Color, Tint
Data save sequence: User Mode ~Device VIDEO
-
2.3.3 Get Data Control
Get Data Command
Get Data Tracking
Manual
ASCII
R(0x52)
A(0x41)
HEX
0x35
0x32
0x34
0x31
Get Data PDP
Current Status
ASCII
R(0x52)
C(0x43)
HEX
0x35
0x32
0x34
0x33
Get Data Total
White Balance
ASCII
G(0x47)
T(0x54)
HEX
0x34
0x37
0x35
0x34
Get Data New
Total White
Balance
ASCII
G(0x47)
P(0x50)
HEX
0x34
0x37
0x35
0x30
Command to read Data saved on EEPROM within the PDP
-
Downloaded From TV-Manual.com Manuals