ERM Neoverse N1 Technical Reference Manual Download

Page: 200 / 241

Purpose

A 32

‑

bit counter that updates at 100Hz. The input clock derives from the 24MHz clock

generator on the N1 board.

Usage constraints

The SYS_100HZ Register is read

‑

only.

Configurations

Available in all N1 board configurations.

Memory offset and full register reset value

See

4.6.1 APB system register summary

on page 4-197

The following table shows the bit assignments.

Table 4-129 SYS_100HZ Register bit assignments

Bits

Name

Type

Function

[31:0]

100HZ_COUNT

Contains the count, at 100Hz, since the last

CB_nRST

reset.

4.6.6

SYS_FLAG Registers

The SYS_FLAG Registers characteristics are:

Purpose

Provide two 32

‑

bit registers, SYS_FLAGS and SYS_NVFLAGS, that contain general

‑

purpose

flags. The application software defines the meaning of the flags. You use the SYS_FLAGSSET,
SYS_FLAGSCLR, SYS_NVFLAGSSET, and SYS_NVFLAGSCLR registers to set and clear
the bits in the Flag Registers.

Usage constraints

The SYS_FLAGS and SYS_NVFLAGS Registers are read

‑

only.

The SYS_FLAGSSET, SYS_FLAGSCLR, SYS_NVFLAGSSET, and SYS_NVFLAGSCLR
Registers are write

‑

only.

Configurations

Available in all N1 SDP configurations.

SYS_FLAGS Register

The SYS_FLAGS Register is one of the two flag registers. It contains the current states of the
flags.

The SYS_FLAGS Register is volatile, that is, a reset signal from the reset push button resets the
SYS_FLAGS Register.

You use the SYS_FLAGSSET Register to set bits in the SYS_FLAGS Register. Write

0b1

to set

the associated flag. Write

0b0

to leave the associated flag unchanged.

You use the SYS_FLAGSCLR Register to clear bits in the SYS_FLAGS Register. Write

0b1

clear the associated flag. Write

0b0

to leave the associated flag unchanged.

4 Programmers model

4.6 APB system registers

101489_0000_02_en

reserved.

4-200

Non-Confidential - Beta

Summary of Contents for Neoverse N1

















































































































































































































































Search results

Summary of Contents for Neoverse N1

Reviews:

Related manuals for Neoverse N1

Brands by name

Popular brands

ERM Neoverse N1, Technical Reference Manual

Search results

Summary of Contents for Neoverse N1

Reviews:

Related manuals for Neoverse N1

Brands by name

Popular brands