CNC8070
R
EF
. 0402
E
RROR
SOLUTIONS
Page 45 of 128
Errors 1000-1999
1403
'#LINK: a coupling (slaving) cannot be defined with a Hirth axis deactivated'
DETECTION
During execution.
CAUSE
An attempt has been made to activate a coupling between Hirth axis while one of them
is deactivated.
SOLUTION
Activate both Hirth axes to be able to activate the coupling.
1404
'The gear associated with the programmed M does not exist'
DETECTION
During execution.
CAUSE
A spindle gear change has been programmed with function M4x (M41 through M44),
but the "x" gear does not exist.
SOLUTION
The number of spindle gears available is indicated by its machine parameter
NPARSETS and, therefore, the CNC only accepts function M41 through M4x with "x"
less than or equal to NPARSETS.
1405
'The S value exceeds the maximum gear'
DETECTION
During execution.
CAUSE
The error comes up, having an AUTOGEAR spindle, when programming a speed
greater than the maximum of any of the gears existing for that spindle.
SOLUTION
The possible solutions are:
• Program a lower spindle speed that may be reached with one of the gears existing
for that spindle.
• Increase, in the machine parameter table, the maximum speed that can be
reached in any of the gears existing for that spindle.
1406
'#CALL: It does not allow to program parameters'
DETECTION
During execution.
CAUSE
The #CALL instructiont does not allow to program parameters.
SOLUTION
Program the call to the subroutine with #PCALL.
1407
'Error when reading the pocket data'
DETECTION
During execution.
CAUSE
When executing a 2D or 3D pocket, the CNC has not been able to decode some of
them. This can happen when the pocket data has been edited manually and a
numerical value has been replaced with a variable or the last bracket of instructions
#DATAP2D, #DATAP3D,… has been eliminated.
SOLUTION
Edit the pocket again with the cycle editor.
1408
'Programming not allowed without a spindle being controlled in position'
DETECTION
During execution.
CAUSE
The programmed function or instruction cannot be executed if the spindle is not
controlled in position.
SOLUTION
The spindle must have an encoder.
1409
'Nesting of T functions with subroutine not allowed'
DETECTION
During execution.
CAUSE
A T has been executed that has a subroutine associated by machine parameter
(TOOLSUB) where another T has been programmed.
SOLUTION
T cannot be programmed within the subroutine associated with T.
1411
'#CD: wrong number of blocks'
DETECTION
During execution.
CAUSE
The number of blocks programmed in the instruction is wrong.
SOLUTION
The maximum number of blocks to analyze is 200.
1412
'#DGWZ: graphics display area defined wrong'
DETECTION
During execution.
CAUSE
The axis limits have been defined wrong in the instruction.
SOLUTION
Both limits may be positive or negative, but the lower limits of an axis must always
be lower than its upper limits.
Summary of Contents for CNC8 070
