manualshive.com logo in svg

Silicon Laboratories Giant Gecko EFM32GG, Reference Manual

The Silicon Laboratories Giant Gecko EFM32GG is a powerful microcontroller, designed for a wide range of applications. Unlock the full potential of this product by downloading the comprehensive "Reference Manual" from our website for free. Access detailed instructions and technical information to maximize your experience with the Giant Gecko EFM32GG.

Share
Download
background image

...the world's most energy friendly microcontrollers

2016-04-28 - Giant Gecko Family - d0053_Rev1.20

20

www.silabs.com

The Cortex-M3, the DMA Controller, and the peripherals run on clocks that can be prescaled separately.
When accessing a peripheral which runs on a frequency equal to or faster than the HFCORECLK, the
number of wait cycles per access, in addition to master arbitration, is given by:

Memory Wait Cycles with Clock Equal or Faster than HFCORECLK

N

cycles

 = 2 + N

slave cycles

,

(5.3)

where N

slave cycles

 is the wait cycles introduced by the slave.

When  accessing  a  peripheral  running  on  a  clock  slower  than  the  HFCORECLK,  wait-cycles  are
introduced  to  allow  the  transfer  to  complete  on  the  peripheral  clock.  The  number  of  wait  cycles  per
access, in addition to master arbitration, is given by:

Memory Wait Cycles with Clock Slower than CPU

N

cycles

 = (2 + N

slave cycles

) x f

HFCORECLK

/f

HFPERCLK

, 

(5.4)

where N

slave cycles

 is the number of wait cycles introduced by the slave.

For general register access, N

slave cycles

 = 1.

More details on clocks and prescaling can be found in Chapter 11 (p. 126) .

5.3 Access to Low Energy Peripherals (Asynchronous Registers)

5.3.1 Introduction

The Low Energy Peripherals are capable of running when the high frequency oscillator and core system
is powered off, i.e. in energy mode EM2 and in some cases also EM3. This enables the peripherals to
perform tasks while the system energy consumption is minimal.

The Low Energy Peripherals are:

• Liquid Crystal Display driver - LCD
• Low Energy Timer - LETIMER
• Low Energy UART - LEUART
• Pulse Counter - PCNT
• Real Time Counter - RTC
• Watchdog - WDOG
• Low Energy Sensor Interface - LESENSE
• Backup RTC - BURTC

All Low Energy Peripherals are memory mapped, with automatic data synchronization. Because the Low
Energy Peripherals are running on clocks asynchronous to the core clock, there are some constraints
on how register accesses can be done, as described in the following sections.

5.3.1.1 Writing

Every Low Energy Peripheral has one or more registers with data that needs to be synchronized into
the Low Energy clock domain to maintain data consistency and predictable operation. There are two
different  synchronization  mechanisms  on  the  Giant  Gecko;  immediate  synchronization,  and  delayed
synchronization.  Immediate  synchronization  is  available  for  the  RTC,  LETIMER  and  LESENSE,  and
results in an immediate update of the target registers. Delayed synchronization is used for the other
Low Energy Peripherals, and for these peripherals, a write operation requires 3 positive edges on the
clock of the Low Energy Peripheral being accessed. Registers requiring synchronization are marked
"Asynchronous" in their description header.

Summary of Contents for Giant Gecko EFM32GG












































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Giant Gecko EFM32GG

Yamaha RCX340 Service Information preview
RCX340
Brand: Yamaha Pages: 5
RAM RP2000 User Manual preview
RP2000
Brand: RAM Pages: 71
Festo CPS-Gate Operating Instructions Manual preview
CPS-Gate
Brand: Festo Pages: 109
Topworx Valvetop DXP Installation, Operation & Maintenance Manual preview
Valvetop DXP
Brand: Topworx Pages: 8
Samcen SCS8000E Administrator'S Manual preview
SCS8000E
Brand: Samcen Pages: 65
Morningstar SUNSAVER SS-10-12V Installation And Operation Manual preview
SUNSAVER SS-10-12V
Brand: Morningstar Pages: 26
NovaStar NovaPro UHD Manual preview
NovaPro UHD
Brand: NovaStar Pages: 11
Nations N32G43 Series User Manual preview
N32G43 Series
Brand: Nations Pages: 654
Kustom Signals Eyewitness HD ICV System Quick Reference Manual preview
Eyewitness HD ICV System
Brand: Kustom Signals Pages: 4
Parker P3HPA Series Manual preview
P3HPA Series
Brand: Parker Pages: 22
Powrmatic Eurotrol 2 Installation & User'S Instructions preview
Eurotrol 2
Brand: Powrmatic Pages: 10
NEEDO MY NEEDO User Manual Book preview
MY NEEDO
Brand: NEEDO Pages: 193
Danfoss ADAP-KOOL AK-CC 750 Service Manual preview
ADAP-KOOL AK-CC 750
Brand: Danfoss Pages: 6
Berker 85865100 Operation Instructions preview
85865100
Brand: Berker Pages: 2
MidNite Solar Brat Instructions Manual preview
Brat
Brand: MidNite Solar Pages: 24
TA DA 516 Manual preview
DA 516
Brand: TA Pages: 8
TDSi GARDiS 1 User Manual preview
GARDiS 1
Brand: TDSi Pages: 23
Xilinx Virtex-5 FXT User Manual preview
Virtex-5 FXT
Brand: Xilinx Pages: 30

Brands by name

Popular brands

Load more brands