TFTP packets
To specify the lowest-numbered IP address configured on a virtual interface as the device source for all TFTP packets, enter commands
such as the following.
device(config)# interface ve 1
device(config-vif-1)# ip address 10.0.0.3/24
device(config-vif-1)# exit
device(config)# ip tftp source-interface ve 1
The commands in this example configure virtual interface 1, assign IP address 10.0.0.3/24 to the interface, then designate the
interface's address as the source address for all TFTP packets.
Syntax:
[no] ip tftp source-interface
{
ethernet
unit
/
slot
/
port
|
loopback
num
|
management
num
|
ve
num
}
The default is the lowest-numbered IP address configured on the port through which the packet is sent. The address therefore changes,
by default, depending on the port.
Syslog packets
To specify the lowest-numbered IP address configured on a virtual interface as the device source for all Syslog packets, enter commands
such as the following.
device(config)# interface ve 1
device(config-vif-1)# ip address 10.0.0.4/24
device(config-vif-1)# exit
device(config)# ip syslog source-interface ve 1
The commands in this example configure virtual interface 1, assign IP address 10.0.0.4/24 to the interface, then designate the
interface's address as the source address for all Syslog packets.
Syntax:
[no] ip syslog source-interface
{
ethernet
unit
/
slot
/
port
|
loopback
num
|
management
num
|
ve
num
}
The default is the lowest-numbered IP or IPv6 address configured on the port through which the packet is sent. The address therefore
changes, by default, depending on the port.
SNTP packets
To specify the lowest-numbered IP address configured on a virtual interface as the device source for all SNTP packets, enter commands
such as the following.
device(config)# interface ve 1
device(config-vif-1)# ip address 10.0.0.5/24
device(config-vif-1)# exit
device(config)# ip sntp source-interface ve 1
The commands in this example configure virtual interface 1, assign IP address 10.0.0.5/24 to the interface, then designate the
interface's address as the source address for all SNTP packets.
Syntax:
[no] ip sntp source-interface
{
ethernet
unit
/
slot
/
port
|
loopback
num
|
management
num
|
ve
num
}
The default is the lowest-numbered IP or IPv6 address configured on the port through which the packet is sent. The address therefore
changes, by default, depending on the port.
SNMP packets
To specify a loopback interface as the SNMP single source trap, enter commands such as the following.
device(config)# interface loopback 1
device(config-lbif-1)# ip address 10.0.0.1/24
Configuring IP parameters - Layer 3 switches
FastIron Ethernet Switch Layer 3 Routing
53-1003627-04
51
Summary of Contents for FastIron SX 1600
