TABLE 23
CLI display of IP forwarding cache - Layer 3 switch (continued)
Field
Description
•
C - Complex Filter
•
W - Wait ARP
•
I - ICMP Deny
•
K - Drop
•
R - Fragment
•
S - Snap Encap
Port
The port through which this device reaches the destination. For
destinations that are located on this device, the port number is shown as
"n/a".
VLAN
Indicates the VLANs the listed port is in.
Pri
The QoS priority of the port or VLAN.
Displaying the IP route table
To display the IP route table, enter the
show ip route
command at any CLI level.
device# show ip route
Total number of IP routes: 514
Start index: 1 B:BGP D:Connected R:RIP S:Static O:OSPF *:Candidate default
Destination NetMask Gateway Port Cost Type
10.1.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.2.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.3.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.4.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.5.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.6.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.7.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.8.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.9.0.0 255.255.0.0 10.1.1.2 1/1/1 2 R
10.10.0.0 255.255.0.0 10.1.1.2 1/1/1 2 S
Syntax:
show ip route
[
ip-addr
[
ip-mask
] [
longer
] [
none-bgp
] ] {
num
|
bgp
|
direct
|
ospf
|
rip
|
static
}
The
ip-addr
parameter displays the route to the specified IP address.
The
ip-mask
parameter lets you specify a network mask or, if you prefer CIDR format, the number of bits in the network mask. If you use
CIDR format, enter a forward slash immediately after the IP address, then enter the number of mask bits (for example: 10.157.22.0/24
for 10.157.22.0 255.255.255.0).
The
longer
parameter applies only when you specify an IP address and mask. This option displays only the routes for the specified IP
address and mask. Refer to the following example.
The
none-bgp
parameter displays only the routes that did not come from BGP4.
The
num
option display the route table entry whose row number corresponds to the number you specify. For example, if you want to
display the tenth row in the table, enter "10".
The
bgp
option displays the BGP4 routes.
The
direct
option displays only the IP routes that are directly attached to the Layer 3 switch.
The
ospf
option displays the OSPF routes.
The
rip
option displays the RIP routes.
The
static
option displays only the static IP routes.
The
default
routes are displayed first.
Displaying IP configuration information and statistics
FastIron Ethernet Switch Layer 3 Routing
132
53-1003627-04
Summary of Contents for FastIron SX 1600
