Freescale Semiconductor MPC561 Reference Manual Download | Manualshive

Page: 623 / 1420

background image

Queued Serial Multi-Channel Module

MPC561/MPC563 Reference Manual, Rev. 1.2

Freescale Semiconductor

15-5

The supervisor-only data space segment contains the QSMCM global registers. These registers define
parameters needed by the QSMCM to integrate with the MCU. Access to these registers is permitted only
when the CPU is operating in supervisor mode.

Assignable data space can be either restricted to supervisor-only access or unrestricted to both supervisor
and user accesses. The supervisor (SUPV) bit in the QSMCM module configuration register
(QSMCMMCR) designates the assignable data space as either supervisor or unrestricted. If SUPV is set,
then the space is designated as supervisor-only space. Access is then permitted only when the CPU is
operating in supervisor mode. If SUPV is clear, both user and supervisor accesses are permitted. To clear
SUPV, the CPU must be in supervisor mode.

The QSMCM assignable data space segment contains the control and status registers for the QSPI and SCI
submodules, as well as the QSPI RAM. All registers and RAM can be accessed on byte (8-bits), half-word
(16-bits), and word (32-bit) boundaries. Word accesses require two consecutive IMB3 bus cycles.

S/U

0x30 5020

SCI2 Control Register 0 (SCC2R0)

S/U

0x30 5022

SCI2 Control Register 1 (SCC2R1)

S/U

0x30 5024

SCI2 Status Register (SC2SR)

S/U

0x30 5026

SCI2 Data Register (SC2DR)

S/U

0x30 5028

QSCI1 Control Register (QSCI1CR)

See <XrefBlue>Table 15-32 for bit descriptions.

S/U

0x30 502A

QSCI1 Status Register (QSCI1SR)

See <XrefBlue>Table 15-33 for bit descriptions.

S/U

0x30 502C –

0x30 504A

Transmit Queue Locations (SCTQ)

S/U

0x30 504C –

0x30 506A

Receive Queue Locations (SCRQ)

S/U

0x30 506C –

0x30 513F

3

Reserved

S/U

0x30 5140 –

0x30 517F

Receive Data RAM (REC.RAM)

S/U

0x30 5180 –

0x30 51BF

Transmit Data RAM (TRAN.RAM)

S/U

0x30 51C0 –

0x30 51DF

Command RAM (COMD.RAM)

1

S = Supervisor access only
S/U = Supervisor access only or unrestricted user access (assignable data space).

2

8-bit registers, such as SPCR3 and SPSR, are on 8-bit boundaries. 16-bit registers such as SPCR0 are on 16-bit
boundaries.

3

Note that QRAM offsets have been changed from the original (modular family) QSMCM.

Table 15-1. QSMCM Register Map (continued)

Access

1

Address

MSB

2

0

LSB

15

«
...
621
622
623
624
625
...
»

Summary of Contents for MPC561













































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MPC561

CEmarking RCX221

Brand: Yamaha Pages: 468

CURTIS DC Series

Brand: NOCO Genius Pages: 2

Brand: Xylem Pages: 2

Brand: Auber Pages: 3

TRULUX DMX 3Z Touch Control

Brand: American Lighting Pages: 2

Brand: KEPCO Pages: 34

Brand: J+J Pages: 91

Brand: D+H Pages: 16

DMC-14 5 Series

Brand: Galil Motion Control Pages: 200

Brand: AGS Pages: 12

PLATINE DE SPA SP800

Brand: BWT Pages: 48

Brand: RIFT Actuators Pages: 23

Brand: Troy-Bilt Pages: 11

L Wired Wall Control

Brand: Haiku Pages: 2

Brand: MRC Pages: 2

Brand: Epsolar Pages: 32

SYG-S7G2-43C-MDK

Brand: FDI Pages: 28

Brand: SRS Labs Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands