Silicon Laboratories EFM32G Reference Manual Download

Page: 195 / 505

...the world's most energy friendly microcontrollers

2014-07-02 - Gecko Family - d0001_Rev1.30

195

www.silabs.com

15.4 Register Map

The offset register address is relative to the registers base address.

Offset

Name

Type

Description

Clock Division Register

0x014

I2Cn_SADDR

Slave Address Register

0x018

I2Cn_SADDRMASK

Slave Address Mask Register

0x01C

I2Cn_RXDATA

Receive Buffer Data Register

0x020

I2Cn_RXDATAP

Receive Buffer Data Peek Register

0x024

I2Cn_TXDATA

Transmit Buffer Data Register

0x028

I2Cn_IF

Interrupt Flag Register

0x02C

I2Cn_IFS

Interrupt Flag Set Register

0x030

I2Cn_IFC

Interrupt Flag Clear Register

0x034

I2Cn_IEN

Interrupt Enable Register

0x038

I2Cn_ROUTE

I/O Routing Register

15.5 Register Description

15.5.1 I2Cn_CTRL - Control Register

Offset

Bit Position

0x000

Reset

0x0

Access

Name

Bit

Name

Reset

Access

Description

31:19

Reserved

To ensure compatibility with future devices, always write bits to 0. More information in Section 2.1 (p. 3)

18:16

CLTO

0x0

Clock Low Timeout

Use to generate a timeout when CLK has been low for the given amount of time. Wraps around and continues counting when the
timeout is reached.

Value

Mode

Description

OFF

Timeout disabled

40PCC

Timeout after 40 prescaled clock cycles. In standard mode at 100 kHz, this results in
a 50us timeout.

80PCC

Timeout after 80 prescaled clock cycles. In standard mode at 100 kHz, this results in
a 100us timeout.

160PCC

Timeout after 160 prescaled clock cycles. In standard mode at 100 kHz, this results
in a 200us timeout.

320PPC

Timeout after 320 prescaled clock cycles. In standard mode at 100 kHz, this results
in a 400us timeout.

1024PPC

Timeout after 1024 prescaled clock cycles. In standard mode at 100 kHz, this results
in a 1280us timeout.

GIBITO

Go Idle on Bus Idle Timeout

Summary of Contents for EFM32G


























































































































































































































































































































































































































































































































Search results

Summary of Contents for EFM32G

Reviews:

Related manuals for EFM32G

Brands by name

Popular brands

Silicon Laboratories EFM32G, Reference Manual

Search results

Summary of Contents for EFM32G

Reviews:

Related manuals for EFM32G

Brands by name

Popular brands