692
ExtremeWare 7.7 Command Reference Guide
Commands for Status Monitoring and Statistics
configure log filter set severity match
configure log filter <filter name> set severity <severity> events
[<event condition> | [all | <event component>]] [match | strict-match]
<type> <value> {and <type> <value> ...}
Description
Sets the severity level of an existing filter item.
Syntax Description
Default
N/A
Usage Guidelines
This command modifies the severity level of an existing filter item describing a particular set of events
and the parameter values of the desired events. Using this command is equivalent to deleting the filter
item from the filter and then adding back a filter item describing the same set of events with a different
severity level. The command can only be used to modify a filter item referring to a set of events with a
severity level, as opposed to one that makes use of only a single severity. It can be used to modify
either “exclude” or “include” filter items.
For example, to change the severity level of the filter item added with this command:
configure log slbFilter2 add exclude events slb.conn severity notice match
source ipaddress 10.1.2.0/24
use the following command:
configure log slbFilter2 set severity info events events slb.conn match
source ipaddress 10.1.2.0/24
Using this single command is preferred to using a
delete
command followed by an
add
command:
configure log slbFilter2 delete exclude events slb.conn severity notice match
source ipaddress 10.1.2.0/24
configure log slbFilter2 add exclude events slb.conn severity info match
filter name
Specifies the filter to configure.
severity
Specifies the severity level to send.
event component
Specifies all the events associated with a particular component.
only
Specifies only events of the specified severity level.
match
Specifies events whose parameter values match the <type> <value> pair.
strict-match
Specifies events whose parameter values match the <type> <value> pair, and possess all
the parameters specified.
type
Specifies the type of parameter to match.
value
Specifies the value of the parameter to match.
and
Specifies additional <type> <value> pairs that must be matched.
Summary of Contents for ExtremeWare 7.7
