manualshive.com logo in svg

Cypress CY8C28 series, Technical Reference Manual

The Cypress CY8C28 series, a versatile microcontroller range, boasts a comprehensive Technical Reference Manual. This invaluable manual can be downloaded for free, providing users with detailed insights and instructions for optimal product utilization. Visit our website 88.208.23.73:8080 to access this essential manual and unlock the full potential of your Cypress CY8C28 series.

Share
Download
background image

342

CY8C28xxx PSoC Programmable System-on-Chip TRM, Document No. 001-52594 Rev. *G

Digital Blocks

Figure 17-4.  CRCPRS LFSR Structure 

LFSR Structure

The LFSR (Linear Feedback Shift register) structure, as
shown in 

Figure 17-4

, is implemented as a modular 

shift

register generator. The least significant block in the chain
inputs the MSb and XORs it with the DATA input, in the case
of CRC computation. For PRS computation, the DATA input
is forced to logic 0 (by input selection); and therefore, the
MSb bus is directly connected to the FB bus. In the case of a
chained block, the data input (DIN) comes directly from the
data output (DO) of the LFSR in the previous block. The
MSb selection, derived from the priority decode of the poly-
nomial, enables one of the tri-state drivers to drive the MSb
bus. 

Determining the CRC Polynomial 

Computation of an n-bit result is generally specified by a
polynomial with n+1 terms, the last of which is X

16

, where

Equation 1

As an example, the CRC-CCIT 16-bit polynomial is:

Equation 2

The CRCPRS hardware assumes the presence of the X

0

term; and therefore, this polynomial can be expressed in 16
bits as 1000 1000 0001 0000b or 8810h. Two consecutive
digital blocks may be allocated to perform this function, with
88h as the MS block polynomial (DR1) and 10h as the LS
block polynomial value. 

Determining the PRS Polynomial

Generally, PRS polynomials are selected from pre-com-
puted reference tables. It is important to note that there are
two common ways to specify a PRS polynomial: simple reg-
ister configuration and modular configuration. In the simple
method, a 

shift register

 is implemented with a reduction

XOR of the MSb and feedback taps as input into the least
significant bit. In the modular method, there is an XOR oper-

ation implemented between each register bit and each tap
point enables the XOR with the MSb for that given bit. The
CRCPRS function implements the modular approach.

These are equivalent methods. However, there is a conver-
sion that should be understood. If tables are specified in
simple register format, then a conversion can be made to
the modular format by subtracting each tap from the MS tap,
as shown in the following example. 

To implement a 7-bit PRS of length 127, one possible code
is [7,6,4,2]s, which is in simple format. The modular format is
[7,7-6,7-4,7-2]m or [7,1,3,5]m which is equivalent to [7, 5, 3,
1]. Determining the polynomial to program is similar to the
CRC example above. Set a 

binary

 bit for each tap (with bit 0

of the register corresponding to tap 1). Therefore, the code
[7,5,3,1] corresponds to 0101 0101b or 55h.

In both the CRC and PRS cases, an appropriate seed value
should be selected. All ones for PRS, or all ones or all zeros
for CRC are typical values. Note that a seed value of all
zeros should not be used in a PRS function, because PRS
counting is inhibited by this seed.

17.1.10.1

Usability Exceptions

The following are usability exceptions for the CRCPRS func-
tion:

1. The polynomial register must only be written when the 

block is disabled.

2. CR1 is not writeable when the CRCPRS is enabled.

17.1.10.2

Block Interrupt

The CRCPRS block has three interrupt sources. The default
one is the compare auxiliary output; that is, the compare out-
put. The second one is data input when CRCPRS is in pass-
by mode. The third one is the KILL signal when KILL_INT is
selected.

DO

0

1

2

7

6

FB Tri-state Bus

DATA

MSB Tri-state Bus

POL

Y

[0

]

POL

Y

[1

]

POL

Y

[6

]

POL

Y

[7

]

2:1

DIN

(From previous block 

DO, if chained.)

(Data input for CRC, if 

PRS, force to logic ‘0’.)

(To next block, 

if chained.)

MSB SEL is determined by a 

priority decode of the MSB, of 

the polynomial across all blocks 

of a CRCPRS function.

MSB 
SEL

SHIFT_

SHIFT_

In Shift mode, the shift registers 
are just like a digital delay line. 
The length is determined by 
polynomial. 

X

0

1

=

CRC

CCIT

–

X

16

X

12

X

5

1

+

+

+

=

Summary of Contents for CY8C28 series




























































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CY8C28 series

Oceanic ZX Service Procedure preview
ZX
Brand: Oceanic Pages: 13
RBI FUTERA XLF Series Control Manual preview
FUTERA XLF Series
Brand: RBI Pages: 128
RBH Access Technologies UNC100 Hardware Manual preview
UNC100
Brand: RBH Access Technologies Pages: 36
S&C PMH Inspection Manual preview
PMH
Brand: S&C Pages: 11
S&C BankGuard PLUS Installation Manual preview
BankGuard PLUS
Brand: S&C Pages: 24
S&C BankGuard PLUS Operation preview
BankGuard PLUS
Brand: S&C Pages: 19
PENGWYN 485-1P-JS Technical Manual preview
485-1P-JS
Brand: PENGWYN Pages: 32
Warner Electric CBC-801-1 Installation Instructions And Service Manual preview
CBC-801-1
Brand: Warner Electric Pages: 6
Bettis TEC2 Quick Start Manual preview
TEC2
Brand: Bettis Pages: 18
Murphy MURPHYMATIC ASM160 Installation And Operation Instructions preview
MURPHYMATIC ASM160
Brand: Murphy Pages: 4
ASROCK iEP-5000G Series Quick Installation Manual preview
iEP-5000G Series
Brand: ASROCK Pages: 2
NXP Semiconductors LPC2880 User Manual preview
LPC2880
Brand: NXP Semiconductors Pages: 362
On-Q lyriQ AU7394 Series Instruction/Installation Sheet preview
lyriQ AU7394 Series
Brand: On-Q Pages: 8
Nuvation BMS NUV100-CI-12 Installation Manual preview
BMS NUV100-CI-12
Brand: Nuvation Pages: 41
National Instruments NI cRIO-9053 User Manual preview
NI cRIO-9053
Brand: National Instruments Pages: 100
Topcon OPUS A3 Eco Get Started preview
OPUS A3 Eco
Brand: Topcon Pages: 9
Pixsys ATR226 User Manual preview
ATR226
Brand: Pixsys Pages: 24
Leviton DECORA ILLUMATECH IPF01-1LX Installation Instructions preview
DECORA ILLUMATECH IPF01-1LX
Brand: Leviton Pages: 2

Brands by name

Popular brands

Load more brands