35
AT+CLIR= [n]
Specifies whether to show your caller ID to the other party when you originate a 64K data
communication.
n=0: In accordance with the service agreement. (when parameter omitted)
n=1: Does not notify the caller ID.
n=2: Notifies the caller ID. (default)
If you enter “AT+CLIR?”, it shows “+CLIR:n,m”.
m=0: CLIR is not activated. (caller ID always notified)
m=1: CLIR is activated. (caller ID always not notified)
m=2: Unknown
m=3: CLIR temporary mode (default for “not notified”)
m=4: CLIR temporary mode (default for “notified”)
ex.
Enter
AT+CLIR=0
Display
AT+CLIR?
Test
AT+CLIR=?
AT+CMEE= [n]
Specifies the error report format of the FOMA terminal.
☛
P38
n=0: Shows “ERROR”. (default and when parameter omitted)
n=1: Shows in the format of “+CME ERROR:xxxx”. (xxxx=numbers)
n=2: Shows in the format of “+CME ERROR:xxxx”. (xxxx=characters)
*1, *2
ex.
Enter
AT+CMEE=0
Display
AT+CMEE?
Test
AT+CMEE=?
AT+CNUM
Shows the Own Number data of the FOMA terminal in the format of “+CNUM:, “number”,type”.
number: Phone number
type=129: Does not show “+81”.
type=145: Shows “+81”.
ex.
Enter
AT+CNUM
Display
None
Test
AT+CNUM=?
AT+COPS=n,2,oper
Sets search method for network operator to connect.
n=0: Auto (Searches network automatically to connect.) (default)
n=1: Manual (Connects to the network operator specified as oper.)
n=2: Cancels (Disconnects) the connection with the operator.
n=3: No mapping
n=4: When you cannot connect to the operator specified as oper, search automatically to connect.
oper: Sets PLMN Number in hexadecimal value.
ex.
Enter
AT+COPS=1
Display
AT+COPS?
Test
AT+COPS=?
AT+CPAS
Displays whether the FOMA terminal can send and receive AT commands to external devices in
“+CPAS:n” format.
n=0: Possible n=1: Impossible n=2: Unknown n=3: Possible and receiving
n=4: Possible and communicating
ex.
Enter
AT+CPAS
Display
None
Test
AT+CPAS=?
AT+CPIN=“pin”
[,“newpin”]
Enters these codes when entry of PIN/PIN2 code or PUK is requested. Entry of “AT+CPIN?” displays
the current status in the “+CPIN:code” format. Execute AT+CPIN=“pin”[,“newpin”] by specifying pin or
newpin depending on the value of code as follows:
ex.
Enter
AT+CPIN=“0000”
Display
AT+CPIN?
Test
AT+CPIN=?
AT+CR= [n]
Specifies whether to display the communication type (packet communication or 64K data
communication) before
CONNECT
is displayed, during line connection.
n=0: Does not show the information. (default and when parameter omitted)
n=1: Shows the information in the format of “+CR:serv”.
serv=SYNC: 64K data communication
serv=GPRS: Packet communication
*1, *2
ex.
Enter
AT+CR=0
Display
AT+CR?
Test
AT+CR=?
AT+CRC= [n]
Specifies whether to use result codes of “+CRING:type” for incoming calls.
n=0: Does not use the result code of “+CRING:type”. (default and when parameter omitted)
n=1: Uses the result code of “+CRING:type”. The example of codes are as follows:
Packet communication
…
+CRING:GPRS “PPP”,,,“mopera.net”
64K data communication
…
+CRING:SYNC
*1, *2
ex.
Enter
AT+CRC=0
Display
AT+CRC?
Test
AT+CRC=?
AT+CREG= [n]
Specifies whether to show the “inside/outside the service area” information.
n=0: Does not show the information. (default and when parameter omitted)
n=1: Shows the information.
If you enter “AT+CREG?”, it shows the information in the format of “+CREG:n,stat”.
stat=0: Outside the service area
stat=1: Inside the service area (home)
stat=4: Unknown
stat=5: Inside the service area (visitor)
*1, *2
ex.
Enter
AT+CREG=0
Display
AT+CREG?
Test
AT+CREG=?
Command
Description & Parameter
Code
Status
pin
newpin
READY
Entry of code not requested
SIM PIN
Entry of PIN code waited
PIN code
None
SIM PIN2
Entry of PIN2 code waited
PIN2 code
None
SIM PUK
PIN locked
PUK
New PIN code
SIM PUK2
PIN2 locked
PUK
New PIN2 code
Next
▲
D905i_E_Manual.fm 35 ページ ２００７年１０月１６日 火曜日 午前１１時５５分
Summary of Contents for FOMA D905I
